TOA Electronics Portable Speaker HS 1200BT User Manual

日本語の取扱説明書は本書の裏面  
をご覧ください。  
OPERATING INSTRUCTIONS  
HS-1200BT  
HS-1200WT  
HS-1500BT  
HS-1500WT  
SPEAKER SYSTEMS  
TABLE OF CONTENTS  
1. SAFETY PRECAUTIONS ........................... 2  
2. GENERAL DESCRIPTION ......................... 3  
3. FEATURES ................................................. 3  
4. DIMENSIONAL DIAGRAM ......................... 3  
5. INPUT TERMINAL SECTION ..................... 4  
6. IMPEDANCE CHANGE .............................. 4  
8. INSTALLATION .......................................... 5  
9. EQUALIZING BY THE  
DIGITAL SIGNAL PROCESSOR ............... 7  
10. SPECIFICATIONS ...................................... 8  
Accessories ................................................. 8  
Optional products ........................................ 8  
7. ABOUT THE INPUT OVERLOAD  
PROTECTION CIRCUIT ............................. 4  
Thank you for purchasing TOA's Speaker System.  
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.  
 
Indicates a potentially hazardous situation which, if mishandled, could  
result in moderate or minor personal injury, and/or property damage.  
CAUTION  
When the Unit is in Use  
• Do not place heavy objects on the unit as this may cause it to fall or break which may result in personal  
injury and/or property damage. In addition, the object itself may fall off and cause injury and/or damage.  
• Make sure that the volume control is set to minimum position before power is switched on. Loud noise  
produced at high volume when power is switched on can impair hearing.  
• Do not operate the unit for an extended period of time with the sound distorting. This is an indication of a  
malfunction, which in turn can cause heat to generate and result in a fire.  
2. GENERAL DESCRIPTION  
TOA’s HS-1200 series and HS-1500 series speakers are 2-way speaker systems made of resin, and feature a  
large diameter woofer. They can be installed in many different applications with combined use of the supplied  
handles and the optional mounting brackets.  
3. FEATURES  
• Tweeter array realizes a 90° horizontal x 40° vertical directivity control at high frequencies  
• Compact and lightweight with its high frequency tweeter array arranged in front of the low frequency woofer  
• Built-in overload protection circuitry for the tweeters  
• Both permanent and temporary installations available  
• Either vertical or horizontal speaker installation available for the permanent installation  
• Easy to carry with a handy handle  
• Both high- and low-impedance applications available by a rotary switch  
4. DIMENSIONAL DIAGRAM  
[Front]  
[Side]  
[Rear]  
Screw terminal  
NEUTRIK NL4MP  
Speakon  
Rotary switch  
B
C
[Bottom]  
Dimensions  
Model  
A
B
C
HS-1200BT/1200WT 448 (17.64) 320 (12.6) 361 (14.21)  
HS-1500BT/1500WT 560 (22.05) 400 (15.75) 451 (17.76)  
Unit: mm (inches)  
3
 
5. INPUT TERMINAL SECTION  
• As the Speakon connector is internally connected in parallel to the screw terminal as shown below, you can  
use either of the two.  
• The usable connector (on the cable end) that matches the NEUTRIK NL4MP Speakon is NEUTRIK NL4FX  
Speakon.  
• Input terminal connection diagram is as shown below.  
[Rear]  
[Input terminal connection diagram]  
Speaker  
Speaker  
Screw terminal  
Speakon  
Screw terminal  
NEUTRIK NL4MP  
Speakon  
6. IMPEDANCE CHANGE  
[Rear]  
To change the impedance, use a standard screwdriver to  
rotate the rotary switch on the speaker's rear panel to select  
the desired input power.  
This switch is factory-preset to 670 Ω.  
Rotary switch  
Note  
When using a high-impedance amplifier, never select 8 Ω,  
as this will damage the speaker and the amplifier.  
Be sure to turn the rotary switch to 8 Ω when using a low-  
impedance amplifier.  
Rotary switch  
The figure represents factory-preset position.  
7. ABOUT THE INPUT OVERLOAD PROTECTION CIRCUIT  
The speaker system has a built-in input overload protection circuitry. If an excessive input signal is applied to  
the speaker, the protection circuitry is activated and cuts off the signal input to the tweeters. A sudden drop of  
the sound volume level during speaker operation indicates that the protection circuitry has been activated. In  
such a case, reduce the amplifier volume and wait. The protection circuitry is automatically reset after  
approximately 10 seconds. After the circuitry is reset, set the volume at a lower level than before.  
Note  
This input overload protection circuitry does not completely protect the speaker component. Depending on the  
nature of the excessive input signal applied to the speaker, there may be damage to the speaker components  
before protection circuitry can operate. Also, if the excessive input signal is applied to the speaker for  
extended periods of time, the protection circuitry may be damaged and will not recover. Take special care that  
the excessive input signal is not applied to the speaker during use.  
4
 
8. INSTALLATION  
8.1. Installing to a Ceiling or Wall  
Install the speaker system to a ceiling or wall using the optional mounting brackets shown below.  
Note  
Refer to the instruction manual enclosed with the HY-1200 series or HY-1500 series Mounting Bracket for its  
mounting details.  
8.1.1. HY-1200VB, HY-1200VW, HY-1500VB and HY-1500VW Mounting Brackets  
(For vertical speaker mounting)  
• These brackets are designed to mount HS series speakers to ceilings or walls vertically.  
HY-1200VB and HY-1200VW: For the HS-1200 series speaker system  
HY-1500VB and HY-1500VW: For the HS-1500 series speaker system  
• They allow speaker’s vertical angle to be adjusted. (Ceiling: From 15° upward to 90° downward, Wall: From  
15° upward to 60° downward)  
Note: They also permit speaker’s horizontal angle to be adjusted in conjunction with the optional HY-C0801 or  
HY-C0801W Ceiling Mount Bracket, or the HY-W0801 or HY-W0801W Wall Mount Bracket.  
[Ceiling installation]  
[Wall installation]  
Mounting Bracket  
Mounting Bracket  
8.1.2. HY-1200HB, HY-1200HW, HY-1500HB and HY-1500HW Mounting Brackets  
(For horizontal speaker mounting)  
• These brackets are designed to mount HS series speakers to ceilings or walls horizontally.  
HY-1200HB and HY-1200HW: For the HS-1200 series speaker system  
HY-1500HB and HY-1500HW: For the HS-1500 series speaker system  
• They allow speaker’s vertical angle to be adjusted. (Ceiling: From 0° horizontal to 90° downward, Wall: From  
15° upward to 60° downward)  
Note: They also permit speaker’s horizontal angle to be adjusted in conjunction with the optional HY-C0801 or  
HY-C0801W Ceiling Mount Bracket, or the HY-W0801 or HY-W0801W Wall Mount Bracket.  
[Ceiling installation]  
[Wall installation]  
Mounting Bracket  
Mounting Bracket  
8.1.3. HY-C0801 and HY-C0801W Ceiling Mount Brackets  
(For ceiling installation, horizontal angle adjustable)  
Installing the HS series speaker to a ceiling in  
conjunction with the HY-1200 series or HY-1500  
series Mounting Bracket permits the speaker's  
horizontal angle to be adjusted.  
Ceiling Moun Bracket  
Mounting Bracket  
The figure at right shows an example of vertical  
speaker installation.  
5
 
8.1.4. HY-W0801 and HY-W0801W Wall Mount Brackets  
(For wall installation, horizontal angle adjustable)  
Wall Mount Bracket  
Mounting Bracket  
Installing the HS series speaker to a wall in  
conjunction with the HY-1200 series or HY-1500  
series Mounting Bracket permits the speaker's  
horizontal angle to be adjusted.  
The figure at right shows an example of vertical  
speaker installation.  
8.1.5. Safety wire installation (For speaker fall prevention)  
When mounting the speaker system to the ceiling or wall, install a safety wire as needed.  
When installing the safety wire, be sure to follow the instructions below.  
Failure to do so may cause the speaker to fall off, resulting in personal  
injury.  
WARNING  
• Use a wire rope of 2 mm (0.08") or more in diameter. (The safety wire is not supplied.)  
• Tighten the safety wire to take up the slack. Otherwise, impact shock at speaker fall may cause the wire-  
connected parts or wire itself to break.  
• Install the safety wire to a place that can structurally support the full weight of load.  
• Screw a speaker suspension bolt (M8) into one of the screw holes on the speaker's bottom surface.  
Then, connect the safety wire to the bolt.  
Installation position of an M8 bolt  
M8 (Screw pitch: 1.25 mm, effective depth: 24 mm)  
Speaker's  
bottom surface  
Note: Unified inch screws cannot be used.  
Changing the orientation of  
the front panel logo  
Turn the logo mark while holding its edges  
to change its orientation.  
8.2. Mounting on the ST-33B Speaker Stand (optional)  
Note  
Refer to the instruction manual enclosed with the  
Speaker Stand for its mounting details.  
Speaker  
Bracket  
Step 1. Fix the bracket supplied with the speaker stand  
to the speaker.  
(supplied with the Stand)  
Step 2. Spread the tripod legs of the stand to their full  
extension.  
Bracket fixing screw  
Note  
Spread the tripod legs until the stays extend  
horizontally.  
Plain washer for M8  
(supplied with the Stand)  
Step 3. Mount the speaker with the bracket fixed onto  
the stand.  
Speaker mounting screw M8  
(supplied with the Stand)  
Step 4. Determine the speaker direction, and tighten  
the bracket fixing screw.  
ST-33B Speaker Stand  
Step 5. Adjust the stand height.  
6
 
8.3. Using as a Floor Monitor  
Notes  
• When installing the speaker system on slippery floor,  
put a non-slip mat under the speaker.  
• Do not kick or stand on the speaker system, as this  
will damage the speaker.  
The figure shows the HS-1200 series.  
8.4. Attaching the Supplied Rubber Feet  
Attach the rubber feet in the case of speaker storage or  
on-floor speaker installation.  
Datum line  
Note  
The rubber foot has a direction (back and forth).  
Align the datum line on the rubber foot with the positioning  
Positioning mark  
mark (  
) on the speaker unit as shown at right.  
Rubber foot  
(accessory)  
Screw M6 x 30 (accessory)  
8.5. Attaching a Handle  
Screw M6 x 30  
(accessory)  
The speaker system comes with a handy carrying handle.  
Attach the handle on the speaker's top surface.  
Handle fitting bracket  
(accessory)  
Handle  
(accessory)  
9. EQUALIZING BY THE DIGITAL SIGNAL PROCESSOR  
The speaker system is capable of providing high-efficiency and wide range reproduction without using an  
equalizer, however more clear and dynamic sound quality can be reproduced by using our digital signal  
processor and performing its settings as shown in the tables below.  
[For the HS-1200BT and HS-1200WT]  
[For the HS-1500BT and HS-1500WT]  
Filter  
HPF (12 dB)  
PEQ  
Frequency (Hz) Gain (dB)  
50  
Q
Filter  
HPF (12 dB)  
PEQ  
Frequency (Hz) Gain (dB)  
50  
Q
1.432  
1.414  
5.764  
5.764  
1.011  
1.204  
1.274  
2.145  
2.871  
2.871  
1.011  
0.718  
520  
1600  
-4.0  
-2.0  
-4.0  
-2.0  
530  
1300  
-3.5  
-3.0  
-3.0  
-3.5  
PEQ  
PEQ  
PEQ  
2300  
PEQ  
2500  
PEQ  
5000  
PEQ  
4500  
PEQ  
14000  
+3.0  
PEQ  
14000  
+1.5  
7
 
10. SPECIFICATIONS  
Model No.  
Enclosure  
HS-1200BT  
HS-1200WT  
HS-1500BT  
HS-1500WT  
Sealed type  
Rated Power  
Continuous pink noise: 100 W, Continuous program: 300 W  
Rated impedance  
8 Ω  
100 V line: 170 Ω (60 W), 330 Ω (30 W), 670 Ω (15 W)  
70 V line: 83 Ω (60 W), 170 Ω (30 W), 330 Ω (15 W), 670 Ω (7.5 W)  
Sensitivity  
97 dB (1 W, 1m)  
70 to 20,000 Hz  
98 dB (1 W, 1m)  
60 to 20,000 Hz  
Frequency Response  
Crossover Frequency  
Directivity Angle  
3 kHz  
Horizontal: 90°, Vertical: 40°  
Low frequency  
Speaker Component  
Low frequency  
30 cm (12") cone type  
38 cm (15") cone type  
High frequency  
Balanced dome tweeter x 6  
High frequency  
balanced dome tweeter x 6  
Input Terminal  
Enclosure  
NEUTRIK NL4MP Speakon and M4 screw terminal (Barrier spacing: 9 mm)  
Polypropylene,  
black  
Polypropylene,  
white  
Polypropylene,  
black  
Polypropylene,  
white  
Finish  
Punched net  
Surface-treated  
steel plate, black  
Surface-treated  
steel plate, white  
Surface-treated  
steel plate, black  
Surface-treated  
steel plate, white  
Operating Temperature  
Dimensions  
–10°C to +50°C (14°F to 122°F)  
361 (w) x 448 (h) x 320 (d) mm  
(14.21" x 17.64" x 12.6")  
451 (w) x 560 (h) x 400 (d) mm  
(17.76" x 22.05" x 15.75")  
Weight  
10 kg (22.05 lb)  
14 kg (30.86 lb)  
Note: The design and specifications are subject to change without notice for improvement.  
• Accessories  
Handle ................................................................................................ 1  
Handle fitting bracket .......................................................................... 2  
Rubber foot ......................................................................................... 2  
Screw M6 x 30 (Used for attaching a handle and rubber foot.) .......... 4  
• Optional products  
Mounting bracket (For vertical speaker mounting): HY-1200VB, HY-1200VW, HY-1500VB, HY-1500VW  
Mounting bracket (For horizontal speaker mounting): HY-1200HB, HY-1200HW, HY-1500HB, HY-1500HW  
Ceiling mount bracket: HY-C0801, HY-C0801W  
Wall mount bracket:  
Speaker stand:  
HY-W0801, HY-W0801W  
ST-33B  
Traceability Information for Europe (EMC directive 2004/108/EC)  
Manufacturer:  
TOA Corporation  
7-2-1, Minatojima Nakamachi, Chuo-ku, Kobe, Hyogo,  
Japan  
Authorized representative:  
TOA Electronics Europe GmbH  
Suederstrasse 282, 20537 Hamburg,  
Germany  
533-06-176-1A  
 

Targus Network Card USB Cable User Manual
Tekkeon Battery Charger HX6711 User Manual
Teledyne Automobile Parts HFC 303 307 User Manual
Toshiba Surge Protector PT930 User Manual
Toshiba TV VCR Combo MV 9DM2 User Manual
TRENDnet Router Net Spot Wireless Access Point User Manual
Troy Bilt Tiller 1634A User Manual
Ultimate Support Systems Switch AX 48 PRO User Manual
Ultra electronic Printer Turbo User Manual
Viking Wok F20900A User Manual