VTech Cordless Telephone 6031 User Manual

Congratulations  
on purchasꢀng your new VTech product.  
Before usꢀng thꢀs telephone, please read the  
Important safety instructions  
on page 30 of thꢀs manual.  
Thꢀs manual has all the feature operatꢀons and troubleshootꢀng necessary to ꢀnstall  
and operate your new VTech telephone. Please revꢀew thꢀs manual thoroughly to  
ensure proper ꢀnstallatꢀon and operatꢀon of thꢀs ꢀnnovatꢀve and feature rꢀch VTech  
product. For support, shoppꢀng, and everythꢀng new at VTech, vꢀsꢀt our websꢀte at  
 
Installation  
Parts checklist  
Remember to save your sales receꢀpt and orꢀgꢀnal packagꢀng ꢀn case ꢀt ꢀs necessary to shꢀp your  
telephone for warranty servꢀce. Check to make sure the telephone package ꢀncludes the followꢀng:  
For replacement  
batterꢀes or power  
adapter, vꢀsꢀt our  
websꢀte at www.  
vtechphones.  
com or call 1 (800)  
595-9511.  
In Canada go to  
com or dꢀal 1 (800)  
267-7377.  
1. Handset  
2. Telephone base  
3. User’s manual  
4. Base power adapter  
5. Battery  
6. Battery compartment cover  
7. Telephone lꢀne cord  
1. Handset  
2. Telephone base  
3. User’s manual  
4. Base power adapter  
5. Battery  
6. Battery compartment cover  
7. Telephone lꢀne cord  
 
1
 
Installation  
Install handset battery  
• Alꢀgn the two holes ꢀn the plug wꢀth the socket pꢀns accordꢀng to the color-coded label  
battery compartment, then snap the plug ꢀnto place.  
ꢀn the  
attery  
If the handset wꢀll  
not be used for a  
long perꢀod of tꢀme,  
remove the battery  
to prevent possꢀble  
leakage.  
To purchase  
replacement  
batterꢀes, vꢀsꢀt our  
websꢀte at www.  
vtechphones.  
com or call 1  
• Place the battery ꢀnto the compartment.  
• Posꢀtꢀon the battery compartment cover and slꢀde ꢀt upwards untꢀl ꢀt clꢀcks ꢀnto place.  
• Put the handset ꢀn the telephone base to charge the new battery for at least 16 hours. The b  
may have enough charge for short calls. For best performance, charge ꢀt for at least 16 hou  
rs.  
You can keep the battery charged by returnꢀng the handset to the telephone base after eac  
When the battery power ꢀs fully depleted, a full recharge takes about 16 hours.  
h use.  
For further ꢀnformatꢀon on batterꢀes, please see the Battery sectꢀon on page 29.  
(800) 595-9511. In  
Canada, go to www.  
vtechcanada.com  
or dꢀal 1 (800) 267-  
7377.  
color-coded label  
2
 
 
Installation  
Telephone base installation  
Install the telephone base and the charger as shown below. Choose a locatꢀon away from any electronꢀc  
equꢀpment and applꢀances such as personal computers, computer routers, televꢀsꢀon sets, mꢀcrowave  
ovens, and refrꢀgerators. Avoꢀd excessꢀve heat, cold, dust or moꢀsture.  
Use only the  
VTech batterꢀes  
and power adapter  
(or equꢀvalent)  
supplꢀed wꢀth  
1. Plug the telephone lꢀne cord  
ꢀnto a telephone wall jack.  
2. Plug the power adapter ꢀnto an electrꢀcal  
outlet not controlled by a wall swꢀtch.  
thꢀs telephone.  
To obtaꢀn a  
replacement, vꢀsꢀt  
our websꢀte at  
com or call 1  
(800) 595-9511.  
In Canada go to  
com or dꢀal 1 (800)  
267-7377.  
Thꢀs power unꢀt  
ꢀs ꢀntended to be  
correctly orꢀented  
in a vertical or floor  
mount posꢀtꢀon.  
The prongs are not  
desꢀgned to hold  
the plug ꢀn place ꢀf  
ꢀt ꢀs plugged ꢀnto a  
ceꢀlꢀng, under-the-  
table or cabꢀnet  
outlet.  
 
3
 
Installation  
Desk/table bracket installation  
The telephone base comes wꢀth the desk/table bracket ꢀnstalled and ready for tabletop use.  
To ꢀnstall the bracket:  
To remove the bracket:  
1. Alꢀgn the tabs of the bracket wꢀth the slots  
at the bottom of the telephone base as  
shown ꢀn the dꢀagram.  
1. Pushthebracketawayfromthetelephone  
base as shown below. Do not remove the  
bracket by force to avoꢀd breakage of  
the tabs.  
2. Slꢀde the bracket towards the center  
of the telephone base untꢀl ꢀt clꢀcks  
ꢀnto place.  
Dial type  
If you have touch-tone servꢀce, your telephone ꢀs ready to use as soon as the battery ꢀs charged.  
If you have pulse (rotary) servꢀce, the dꢀal type must be changed. To change the dꢀal type, see  
Dial type sectꢀon on page 12.  
4
 
 
Installation  
If you subscribe to DSL service  
If you receꢀve hꢀgh speed ꢀnternet through your telephone lꢀne (commonly referred to as DSL), and  
you are experꢀencꢀng ꢀnterference durꢀng telephone conversatꢀons and/or your caller ID features are  
not functioning properly, install a DSL filter to the telephone line between the telephone base and  
the telephone wall jack. Contact your DSL provider for a DSL filter.  
DSL filter (for  
DSL users)  
To sꢀngle telephone jack (RJ11C)  
Telephone lꢀne cord  
 
5
 
Telephone settings  
Handset layout  
1. Earpꢀece  
2.  
3.  
4.  
/
(dꢀrectory/volume)  
(speakerphone)  
/FLASH  
1
5. Dꢀalꢀng keys (0-9,*,#)  
6. REDIAL/PAUSE  
7. Mꢀcrophone  
8
8. Handset dꢀsplay  
9. MENU/SELECT  
2
3
9
10. CID/  
(caller ID/volume)  
11. OFF/CLEAR  
12. MUTE  
10  
11  
4
13. REMOVE  
5
12  
13  
6
7
6
 
 
Telephone settings  
Telephone base layout  
1. CHARGE lꢀght  
2. IN USE lꢀght  
3. VOICEMAIL lꢀght  
4. FIND HANDSET  
1
2
3
4
 
7
 
Telephone settings  
Date and time  
YeAr  
dAte  
tIMe  
200\  
\1/01  
• Press MENU/SELECT to dꢀsplay menu when ꢀn ꢀdle mode.  
When enterꢀng  
the date or tꢀme, ꢀf  
the dꢀgꢀt ꢀs sꢀngle,  
a zero must be  
entered first (i.e.  
ꢀf the tꢀme ꢀs 6:08,  
you must enter  
0608).  
• Press  
or  
to reach DaTE/TIME. Press MENU/SELECT.  
• Use the keypad to set the year. Press MENU/SELECT.  
• Use the keypad to set the date. Press MENU/SELECT.  
Use the keypad to set the tꢀme. Press  
or  
to select a.m. or p.m.  
Press MENU/SELECT.  
• The screen dꢀsplays STorED and you’ll hear a confirmation beep.  
\2:12AM  
ring melody  
There are ten handset rꢀnger melodꢀes to choose from.  
• Press MENU/SELECT to dꢀsplay menu when ꢀn ꢀdle mode.  
• Press  
or  
to reach SETUP HS. Press MENU/SELECT.  
• Press  
or  
to reach rINg MELoDy. Press MENU/SELECT, a  
rING MelodY  
rING voluMe  
checkmark ꢀs shown next to the current rꢀng melody.  
• Press  
or  
to scroll through the choꢀces and a sample of each  
rꢀng melody wꢀll be played. Press MENU/SELECT.  
• The screen dꢀsplays STorED and you’ll hear a confirmation beep.  
MelodY 1  
MelodY 2  
Stored  
8
 
 
Telephone settings  
ring volume  
The handset ringer volume can be adjusted from five available levels.  
The handset wꢀll  
not rꢀng when the  
rꢀnger volume ꢀs at  
the lowest settꢀng.  
A rꢀnger off ꢀcon  
wꢀll be dꢀsplayed.  
• Press MENU/SELECT to dꢀsplay menu when ꢀn ꢀdle mode.  
• Press  
• Press  
• Press  
or  
or  
or  
to reach SETUP HS. Press MENU/SELECT.  
to reach rINg voLUME. Press MENU/SELECT.  
to scroll through the choꢀces and a sample of each rꢀng  
volume wꢀll be played.  
Whꢀle the  
telephone ꢀs  
• Press MENU/SELECT to confirm. The screen displays STorED and  
rꢀngꢀng, you  
you’ll hear a confirmation beep.  
toNeS  
HANdSet NAMe  
can temporarꢀly  
sꢀlence the rꢀnger  
by pressꢀng  
oFF/CLEar or  
MUTE. A rꢀnger  
Battery low tone  
The handset ꢀs preset to beep when the battery level ꢀs low.  
off ꢀcon  
wꢀll  
• Press MENU/SELECT to dꢀsplay the menu when ꢀn ꢀdle mode.  
be dꢀsplayed. The  
next call wꢀll rꢀng  
normally.  
BAtterY low  
out of rANGe  
• Press  
• Press  
• Press  
or  
or  
or  
to reach SETUP HS. Press MENU/SELECT.  
to reach ToNES. Press MENU/SELECT.  
to reach BaTTEry Low. Press MENU/SELECT.  
• A checkmark ꢀs shown next to the current selectꢀon. Press  
or  
to choose oN or oFF. Press MENU/SELECT.  
• The screen dꢀsplays STorED and you’ll hear a confirmation beep.  
oN  
off  
 
9
 
Telephone settings  
out of range tone  
The handset wꢀll beep durꢀng a conversatꢀon when ꢀt ꢀs out of range from  
the telephone base. Thꢀs tone ꢀs preset to oN.  
toNeS  
HANdSet NAMe  
Press oFF/CLEar  
at anytꢀme to the  
return to prevꢀous  
screen.  
Press and hold  
oFF/CLEar at  
anytꢀme to exꢀt the  
menu.  
• Press MENU/SELECT to dꢀsplay the menu when ꢀn ꢀdle mode.  
• Press  
• Press  
• Press  
or  
or  
or  
to reach SETUP HS. Press MENU/SELECT.  
to reach ToNES. Press MENU/SELECT.  
to reach oUT oF raNgE. Press MENU/SELECT.  
out of rANGe  
KeY BeePS  
• A checkmark ꢀs shown next to the current selectꢀon. Press  
or  
to choose oN or oFF. Press MENU/SELECT.  
• The screen dꢀsplays STorED and you’ll hear a confirmation beep.  
Key tone  
oN  
off  
The handset ꢀs preset to beep whenever any button ꢀs pressed. To  
change thꢀs settꢀng:  
• Press MENU/SELECT to dꢀsplay the menu when ꢀn ꢀdle mode.  
• Press  
• Press  
• Press  
or  
or  
or  
to reach SETUP HS. Press MENU/SELECT.  
to reach ToNES. Press MENU/SELECT.  
to reach KEy BEEPS. Press MENU/SELECT.  
• A checkmark ꢀs shown next to the current selectꢀon. Press  
or  
to  
select oN or oFF. Press MENU/SELECT.  
• The screen dꢀsplays STorED and you’ll hear a confirmation beep.  
10  
 
 
Telephone settings  
Edit handset name  
HANdSet NAMe  
lANGuAGe  
• Press MENU/SELECT to dꢀsplay the menu when ꢀn ꢀdle mode.  
A handset name  
can be up to 14  
characters only.  
Only handset  
dꢀsplay screens  
are affected by  
the language  
settꢀng.  
• Press  
• Press  
or  
or  
to reach SETUP HS. Press MENU/SELECT.  
to reach HaNDSET NaME. Press MENU/SELECT.  
• Press rEMovE to backspace and erase characters. Press and hold  
eNter NAMe  
HANdSet\  
rEMovE to delete the entꢀre entry. Press to alternate between  
*
uppercase and lowercase.  
• Use the keypad to enter characters (see the chart on page 17). Press  
MENU/SELECT.  
a
• The screen dꢀsplays STorED and you’ll hear a confirmation beep.  
Language  
To change the language for all screen dꢀsplays:  
lANGuAGe  
reSet  
• Press MENU/SELECT to dꢀsplay menu when ꢀn ꢀdle mode.  
• Press  
• Press  
or  
or  
to reach SETUP HS. Press MENU/SELECT.  
to reach LaNgUagE. Press MENU/SELECT.  
• A checkmark ꢀs shown next to the current selectꢀon. Press  
to choose the desꢀred language.  
or  
• Press MENU/SELECT.  
• The screen dꢀsplays STorED and you’ll hear a confirmation beep.  
 
11  
 
Telephone settings  
Dial type  
dIAl tYPe  
clr voIceMAIl  
The dꢀal type ꢀs preset to touch tone. If you have pulse (rotary) servꢀce,  
the dꢀal type must be changed.  
The clear voꢀcemaꢀl  
feature only turns off  
the dꢀsplayed NEw  
voICEMaIL message  
and voICEMaIL  
• Press MENU/SELECT to dꢀsplay menu when ꢀn ꢀdle mode.  
• Press  
• Press  
or  
or  
to reach SETUP BS. Press MENU/SELECT.  
to reach DIaL TyPE. Press MENU/SELECT.  
lꢀght on the telephone  
base. It does not  
toNe  
PulSe  
• A checkmark ꢀs shown next to the current selectꢀon. Press  
or  
to choose between ToNE and PULSE. Press MENU/SELECT.  
• The screen dꢀsplays STorED and you’ll hear a confirmation beep.  
delete your voꢀcemaꢀl  
message(s). Use  
thꢀs feature when the  
telephone ꢀndꢀcates  
there ꢀs voꢀcemaꢀl  
Clear voicemail  
when you have none  
or you have accessed  
your voꢀcemaꢀl from a  
remote locatꢀon (whꢀle  
away from home). If  
there ꢀs actually a new  
voꢀcemaꢀl message,  
your local telephone  
company wꢀll contꢀnue  
to send a sꢀgnal whꢀch  
wꢀll cause the NEw  
voICEMaIL message  
ꢀn the handset and  
the telephone base  
voICEMaIL lꢀght to  
flash.  
If you subscrꢀbe to voꢀcemaꢀl servꢀces provꢀded by your local telephone  
company, NEw voICEMaIL wꢀll appear on the handset dꢀsplay and  
the voICEMaIL light on the telephone base will flash when you have  
a new voꢀcemaꢀl message. Thꢀs feature allows you to turn off these  
ꢀndꢀcators.  
clr voIceMAIl  
reSet  
• Press MENU/SELECT to dꢀsplay the menu when ꢀn ꢀdle mode.  
• Press  
• Press  
or  
or  
to reach SETUP BS. Press MENU/SELECT.  
to reach CLr voICEMaIL. Press MENU/SELECT.  
INdIcAtor off?  
• The screen dꢀsplays INDICaTor oFF? Press MENU/SELECT.  
• The screen dꢀsplays STorED and you’ll hear a confirmation beep.  
12  
 
 
Telephone settings  
reset to default settings  
The handset and the telephone base can be ꢀndꢀvꢀdually reset to theꢀr  
default settꢀngs by selectꢀng rESET ꢀn the SETUP HS or SETUP BS menus  
respectꢀvely.  
reSet  
rING MelodY  
When the handset  
or telephone base  
settꢀngs are reset  
to default, all ꢀtems  
stored ꢀn memory  
wꢀll be deleted.  
• Press MENU/SELECT to dꢀsplay menu when ꢀn ꢀdle mode.  
Press  
or  
or  
to reach SETUP HS or SETUP BS. Press MENU/SELECT.  
to reach rESET. Press MENU/SELECT.  
reSet?  
• Press  
Thꢀs ꢀncludes the  
dꢀrectory and call  
log entrꢀes.  
• The screen dꢀsplays rESET? Press MENU/SELECT to confirm or  
oFF/CLEar to exꢀt to prevꢀous menu.  
• If selection is confirmed, the screen displays STorED and you’ll hear a  
confirmation beep.  
Temporary tone dialing  
If you have pulse (rotary) servꢀce, you can change from pulse to touch tone  
dꢀalꢀng durꢀng a call by pressꢀng ToNE. Thꢀs ꢀs useful ꢀf you need to send touch  
*
tone sꢀgnals for access to telephone bankꢀng or long dꢀstance servꢀces.  
• Press  
/FLaSH.  
• Press ToNE. Buttons pressed after thꢀs send touch tone sꢀgnals.  
*
• Dꢀal the number.  
After hangꢀng up, the telephone automatꢀcally returns to pulse dꢀal servꢀce.  
 
13  
 
Basic operation  
Make, answer and end calls  
Press  
-or-  
/FLaSH or  
, then use the keypad to dꢀal a number.  
Press  
or to  
adjust the lꢀstenꢀng  
volume durꢀng a  
conversatꢀon.  
Dꢀal a number (press rEMovE to make correctꢀons) and then press  
/FLaSH or  
.
• Press  
ꢀncomꢀng call.  
/FLaSH,  
or any dꢀalꢀng keys (0-9, or #) to answer an  
*
• Press oFF/CLEar or put the handset back ꢀn the telephone base to  
end a call.  
• The call tꢀmer wꢀll be actꢀvated durꢀng a call to show call duratꢀon.  
options while on calls  
Speakerphone  
Press  
to alternate between speakerphone and normal handset use.  
Mute  
Press MUTE on the handset to sꢀlence the mꢀcrophone durꢀng a  
conversatꢀon. You can stꢀll hear the caller but the caller cannot hear you.  
• The screen dꢀsplays MUTE.  
• Press MUTE agaꢀn to resume conversatꢀon.  
Call waiting  
If you subscrꢀbe to call waꢀtꢀng servꢀce and you are on a call when a new call  
comes ꢀn, you wꢀll hear a beep. The caller ID ꢀnformatꢀon wꢀll be dꢀsplayed  
ꢀf you subscrꢀbe to caller ID servꢀce from your local telephone company.  
PHoNe 00:00:10  
595-9511  
• Press  
/FLaSH on the handset to answer the ꢀncomꢀng call and put  
the current call on hold.  
MUTE  
• Press  
/FLaSH at anytꢀme to alternate between calls.  
14  
 
 
Basic operation  
Find handset  
• Press FIND HaNDSET on the telephone base to locate the handset when  
ꢀn ꢀdle mode. The handset wꢀll rꢀng and PagINg will flash on its screen.  
• Press FIND HaNDSET agaꢀn or put the handset back on the telephone  
base to stop the pagꢀng tone.  
PAGING  
 
15  
 
advanced operation  
Directory  
The dꢀrectory can store up to 50 entrꢀes. Each entry may consꢀst of a  
number up to 24 dꢀgꢀts and a name up to 15 characters.  
eMPtY  
• The screen dꢀsplays EMPTy ꢀf there ꢀs no record ꢀn the dꢀrectory.  
• The screen dꢀsplays FULL ꢀf the dꢀrectory ꢀs full.  
review the directory  
dIrectorY  
cAll loG  
• Press  
• Press  
-or-  
/
to enter the dꢀrectory.  
or  
to browse and press oFF/CLEar to exꢀt.  
• Press MENU/SELECT to dꢀsplay menu when ꢀn ꢀdle mode.  
• Press  
• Press  
• Press  
or  
or  
or  
to reach DIrECTory. Press MENU/SELECT.  
to reach rEvIEw. Press MENU/SELECT.  
to browse and press oFF/CLEar to exꢀt.  
revIew  
Store  
Search the directory  
Entrꢀes are sorted alphabetꢀcally and names begꢀnnꢀng wꢀth numbers  
are listed first.  
vtecH  
1-595-9511  
An alphabetꢀcal search can be done after enterꢀng the dꢀrectory. Enter  
the first letter of the name using the chart on page 17. The first name  
begꢀnnꢀng wꢀth that letter wꢀll be dꢀsplayed.  
For example, press 5 (JKL) once to find Jenny, twice to find Kristen, or  
three times to find Linda.  
-or-  
You can search the dꢀrectory by pressꢀng  
or  
on the handset.  
16  
 
 
advanced operation  
Character chart  
Use the keypad and the chart below to enter a name (up to 15 characters). Each press of a partꢀcular  
key causes the characters to be dꢀsplayed ꢀn the followꢀng order:  
Press  
*
repeatedly to  
alternate between  
uppercase  
and lowercase  
when enterꢀng  
characters.  
Characters by number of key presses  
Number key  
1
2
1
3
*
4
?
2
3
4
5
6
S
8
Z
5
!
6
/
7
(
8
)
9
1
2
3
4
5
6
7
8
9
0
*
space  
A
D
G
J
B
E
H
K
N
Q
U
X
C
F
I
L
O
R
V
Y
M
P
T
7
9
W
0
Uppercase/lowercase  
,
#
#
,
-
.
&
• Press rEMovE to backspace and erase a sꢀngle character.  
• Press and hold rEMovE to delete the entꢀre entry.  
• Press and hold rEDIaL/PaUSE to ꢀnsert a dꢀalꢀng pause (P wꢀll be dꢀsplayed) when enterꢀng a  
telephone number.  
 
17  
 
advanced operation  
Store a directory entry  
Store  
revIew  
• Press MENU/SELECT twꢀce to enter the DIrECTory.  
• Press  
or  
to reach STorE and then press MENU/SELECT.  
• The screen dꢀsplays ENTEr NUMBEr. Use the keypad to enter the  
number and then press MENU/SELECT.  
• The screen dꢀsplays ENTEr NaME. Use the keypad to enter the  
characters and then press MENU/SELECT.  
eNter NuMBer  
• The screen dꢀsplays STorED and you’ll hear a confirmation beep.  
Dial a directory entry  
eNter NAMe  
a
• Press  
/
to enter the dꢀrectory.  
• Press  
or  
to scroll to the desꢀred entry, or use the alphabetꢀcal  
search to find it.  
• Press /FLaSH or  
-or-  
• Press MENU/SELECT to dꢀsplay menu when ꢀn ꢀdle mode.  
to dꢀal.  
Stored  
• Press  
• Press  
• Press  
or  
or  
or  
to reach DIrECTory. Press MENU/SELECT.  
to reach rEvIEw. Press MENU/SELECT.  
to scroll to the desꢀred entry, or use the alphabetꢀcal  
search to find it.  
• Press /FLaSH or  
to dꢀal.  
18  
 
 
advanced operation  
Edit an entry in the directory  
eNter NuMBer  
eNter NAMe  
• Press  
/
or MENU/SELECT three tꢀmes to enter the dꢀrectory.  
Press oFF/CLEar  
to return to the  
prevꢀous screen.  
Press and hold  
oFF/CLEar to  
exꢀt the menu at  
anytꢀme.  
• Press  
or  
to scroll to the desꢀred entry or use the alphabetꢀcal  
search to find the number. Press MENU/SELECT.  
The screen dꢀsplays ENTEr NUMBEr. Use rEMovE and the keypad  
to edꢀt the number and press MENU/SELECT.  
• The screen dꢀsplays ENTEr NaME. Use rEMovE and the keypad to  
edꢀt the name and then press MENU/SELECT.  
• The screen dꢀsplays STorED and you’ll hear a confirmation beep.  
a
Delete from the directory  
Stored  
• Press  
• Press  
/
or MENU/SELECT three tꢀmes to enter the dꢀrectory.  
or  
to scroll to the desꢀred entry.  
To delete an entry  
• Press rEMovE.  
• The screen dꢀsplays DELETED and you’ll hear a confirmation beep.  
deleted  
To delete all entries  
• Press and hold rEMovE.  
• The screen dꢀsplays DELETE aLL? Press MENU/SELECT.  
• The screen dꢀsplays DELETED and you’ll hear a confirmation beep.  
delete All?  
 
19  
 
advanced operation  
about caller ID  
If you subscrꢀbe to caller ID servꢀce from your local telephone company, thꢀs feature dꢀsplays the  
name and telephone number of the caller before answerꢀng a call (even when you are on another  
call). The caller ID features of thꢀs product wꢀll work only ꢀf you subscrꢀbe to caller ID servꢀce and  
both you and the caller are ꢀn areas offerꢀng caller ID servꢀce, and ꢀf both telephone companꢀes use  
compatꢀble equꢀpment.  
Contact your local telephone company ꢀf:  
you have both caller ID and call waꢀtꢀng, but as separate servꢀces (you may need combꢀned servꢀce),  
• you have only caller ID servꢀce, or only call waꢀtꢀng servꢀce,  
• you do not subscrꢀbe to caller ID or call waꢀtꢀng servꢀces but wꢀsh to try them.  
There may be fees for these servꢀces, and they may not be avaꢀlable ꢀn all areas.  
Thꢀs product can be used wꢀthout subscrꢀbꢀng to eꢀther caller ID or combꢀned caller ID wꢀth call waꢀtꢀng  
servꢀce, although the caller ID features of thꢀs product wꢀll not functꢀon.  
20  
 
 
advanced operation  
Call log  
The ꢀnformatꢀon of the caller wꢀll be dꢀsplayed ꢀf you subscrꢀbe to caller ID  
servꢀce from your local telephone company.  
Due to regꢀonal  
servꢀce  
dꢀfferences,  
the caller ID  
ꢀnformatꢀon  
JoHNNY fu  
2-345-6789  
New  
• The call log can store up to 50 entrꢀes.  
• Each entry may consꢀst of a number up to 20 dꢀgꢀts and a name up to  
15 characters. If the number consꢀsts of more than 20 dꢀgꢀts, the last 20  
dꢀgꢀts wꢀll be dꢀsplayed and stored. If the name consꢀsts of more than 15  
characters, the first 15 characters will be displayed and stored.  
05:27PM 11/23  
may not be  
avaꢀlable for  
every ꢀncomꢀng  
call. In addꢀtꢀon,  
the callers may  
ꢀntentꢀonally  
block theꢀr name  
and/or telephone  
number.  
• Entrꢀes are dꢀsplayed ꢀn chronologꢀcal order wꢀth the newest  
entry first.  
eMPtY  
• When the call log ꢀs full, the oldest entry wꢀll be deleted to make room  
for the new ꢀncomꢀng call ꢀnformatꢀon.  
• The screen dꢀsplays EMPTy ꢀf there ꢀs no record ꢀn the call log.  
• The screen dꢀsplays NEw ꢀf there are new call log entrꢀes (mꢀssed and  
unread calls).  
The tꢀme ꢀs  
automatꢀcally set  
and updated wꢀth  
ꢀncomꢀng caller ID  
ꢀnformatꢀon ꢀf you  
subscrꢀbe to thꢀs  
servꢀce.  
• Duplꢀcate or anonymous calls (no caller ID ꢀnformatꢀon) wꢀll be stored  
ꢀn the call log.  
review the call log  
• Press CID/ to enter the call log.  
-or-  
• Press MENU/SELECT. Press  
• Press MENU/SELECT and then press  
or  
to select CaLL Log.  
or to browse through the  
entrꢀes.  
• The name (ꢀf avaꢀlable), number, date and tꢀme of the ꢀncomꢀng call are  
dꢀsplayed on the screen.  
 
21  
 
advanced operation  
Dial a call log number  
• Press CID/ to enter the call log.  
-or-  
eNter NAMe  
a
Whꢀle revꢀewꢀng  
the call log, press  
# repeatedly to  
dꢀsplay the other  
dꢀalꢀng optꢀons.  
The avaꢀlable  
• Press MENU/SELECT. Press  
or  
to select CaLL Log.  
• Press MENU/SELECT and then press  
or  
to scroll to the desꢀred  
entry.  
• Press  
/FLaSH or  
to dꢀal.  
Stored  
optꢀons are: (1  
+ area code +  
number, area code  
+ number, 1 +  
number, number  
only). The varꢀous  
dꢀalꢀng optꢀons are:  
Store a call log number  
• Press CID/ to enter the call log.  
-or-  
• Press MENU/SELECT. Press  
• Press MENU/SELECT and then press  
or  
to select CaLL Log.  
or  
to scroll to the desꢀred  
entry.  
595-9511  
1-595-9511  
• Press MENU/SELECT and the screen dꢀsplays ENTEr NaME.  
• Use the keypad to enter the name and then press MENU/SELECT.  
• The screen dꢀsplays STorED and you’ll hear a confirmation beep.  
800-595-9511  
1-800-595-9511  
22  
 
 
advanced operation  
Delete from the call log  
• Press CID/ to enter the call log.  
Press oFF/CLEar  
to return to the  
prevꢀous screen.  
Press and hold  
oFF/CLEar to  
exꢀt the menu at  
anytꢀme.  
-or-  
• Press MENU/SELECT. Press  
press MENU/SELECT.  
or  
to select CaLL Log, then  
To delete one entry  
Press  
• The screen dꢀsplays DELETED and you’ll hear a confirmation beep.  
or  
to scroll to the desꢀred entry and then press rEMovE.  
deleted  
To delete all entries  
• Press and hold rEMovE when ꢀn the CaLL Log.  
• The screen dꢀsplays DELETE aLL? Press MENU/SELECT.  
• The screen dꢀsplays DELETED and you’ll hear a confirmation beep.  
delete All?  
 
23  
 
advanced operation  
redial  
The redꢀal lꢀst can store up to 10 of the most recently dꢀaled numbers.  
• When there are already 10 entrꢀes ꢀn the redꢀal lꢀst, the oldest entry  
wꢀll be deleted to make room as you place addꢀtꢀonal calls.  
• The screen dꢀsplays EMPTy ꢀf there are no records ꢀn the lꢀst.  
review redial  
• Press rEDIaL/PaUSE to enter the redꢀal lꢀst.  
• Press  
or  
to browse through the entrꢀes.  
Store a redial number to the directory  
• Press rEDIaL/PaUSE to enter the redꢀal lꢀst.  
• Press  
or  
to scroll to the desꢀred entry. Press MENU/SELECT.  
• The screen dꢀsplays ENTEr NaME.  
• Use the keypad to enter the name and then press MENU/SELECT.  
• The screen dꢀsplays STorED and you’ll hear a confirmation beep.  
24  
 
 
advanced operation  
Dial from redial  
• Press rEDIaL/PaUSE to enter the redꢀal lꢀst.  
Press oFF/CLEar  
to return to the  
prevꢀous screen.  
Press and hold  
oFF/CLEar to  
exꢀt the menu at  
anytꢀme.  
• Press  
• Press  
or  
to scroll to the desꢀred entry.  
to dꢀal.  
/FLaSH or  
Delete from redial  
• Press rEDIaL/PaUSE to enter the redꢀal lꢀst.  
To delete one entry  
deleted  
Press  
or  
to scroll to the desꢀred entry and then press rEMovE.  
• The screen dꢀsplays DELETED and you’ll hear a confirmation beep.  
To delete all entries  
• Press and hold rEMovE.  
• The screen dꢀsplays DELETE aLL? Press MENU/SELECT.  
• The screen dꢀsplays DELETED and you’ll hear a confirmation beep.  
delete All?  
 
25  
 
Handset and telephone base indicators  
Handset light  
• On when the handset speakerphone ꢀs ꢀn use.  
Telephone base lights  
IN USE  
• Flashes when there ꢀs an ꢀncomꢀng call.  
• On when the handset ꢀs ꢀn use.  
voICEMaIL  
CHargE  
• Flashes when there ꢀs a new network message (A subscrꢀptꢀon servꢀce from your  
local telephone company ꢀs requꢀred).  
• On when the handset ꢀs ꢀn the telephone base.  
Handset icons  
Rꢀnger off.  
• Cycles (low, medꢀum, and full) when handset battery ꢀs chargꢀng.  
• Flashes when the battery power ꢀs low.  
(Battery ꢀndꢀcator)  
26  
 
 
Handset display screen messages  
Display:  
when:  
There ꢀs an ꢀncomꢀng call.  
cAll  
A handset wꢀth low battery has been placed on the telephone base to recharge.  
The cordless handset ꢀs searchꢀng for the telephone base.  
There are no entrꢀes ꢀn the call log, dꢀrectory, or redꢀal lꢀst.  
You have just ended a call.  
cHArGING  
coNNectING...  
eMPtY  
eNded  
The dꢀrectory ꢀs full.  
full  
Another handset connected to the same lꢀne ꢀs ꢀn use.  
The battery needs to be recharged.  
lINe IN uSe  
low BAtterY  
Mute  
The mꢀcrophone ꢀs muted temporarꢀly durꢀng a conversatꢀon.  
There are un-revꢀewed calls ꢀn the call log.  
There ꢀs new voꢀcemaꢀl message.  
New  
New voIceMAIl  
Not AvAIlABle  
There ꢀs no lꢀne or the handset ꢀs out of range from the telephone base.  
-or-  
If one handset ꢀs already vꢀewꢀng the call log and another handset attempts to  
revꢀew ꢀt.  
There ꢀs no telephone lꢀne connected.  
No lINe  
PAGING  
The handset locator has been actꢀvated or the handset ꢀs beꢀng paged.  
 
27  
 
Handset display screen messages  
Display:  
when:  
The handset ꢀs ꢀn use.  
PHoNe  
The battery ꢀs very low. The handset should be placed on the telephone base  
to recharge.  
PlAce IN cHArGer  
The battery ꢀs not ꢀnstalled or not ꢀnstalled properly ꢀn the handset.  
-or -  
The battery needs to be replaced.  
wArNING  
cHecK BAtterY!  
-or -  
An ꢀncorrect battery has been ꢀnstalled by mꢀstake. Use only the supplꢀed  
VTech battery, or equꢀvalent.  
Call log display screen messages  
Display:  
when:  
The caller ꢀs blockꢀng name ꢀnformatꢀon.  
The caller ꢀs blockꢀng telephone number ꢀnformatꢀon.  
The caller ꢀs blockꢀng name and number ꢀnformatꢀon.  
Thꢀs caller’s name ꢀs unavaꢀlable.  
PrIvAte NAMe  
PrIvAte NuMBer  
PrIvAte cAller  
uNKNowN NAMe  
Thꢀs caller’s number ꢀs unavaꢀlable.  
No call ꢀnformatꢀon ꢀs avaꢀlable about thꢀs caller.  
Thꢀs ꢀs a long dꢀstance call.  
uNKNowN NuMBer  
uNKNowN cAller  
loNG dIStANce or  
l (before caller’s number)  
28  
 
 
Battery  
after the battery is fully charged for 16 hours, you can expect the following performance:  
Operatꢀon  
Operatꢀng tꢀme  
10 hours  
Whꢀle ꢀn use (talkꢀng)  
Whꢀle not ꢀn use (standby*)  
100 hours  
*Handset ꢀs off the telephone base but not ꢀn use.  
The battery needs chargꢀng when:  
• A new battery ꢀs ꢀnstalled ꢀn the handset.  
• Battery indicator on screen is flashing.  
CaUTIoN:  
1. Use only the supplꢀed battery (part number 89-1326-00-00) or equꢀvalent. To order a replacement, vꢀsꢀt our websꢀte at  
2. Do not dispose of the battery in a fire. Check with local waste management codes for special disposal instructions.  
3. Do not open or mutꢀlate the battery(ꢀes). Released electrolyte ꢀs corrosꢀve and may cause burns or ꢀnjury to the eyes or  
skꢀn. The electrolyte may be toxꢀc ꢀf swallowed.  
4. Exercꢀse care ꢀn handlꢀng batterꢀes ꢀn order not to create a short cꢀrcuꢀt by lettꢀng them come ꢀnto contact wꢀth conductꢀve  
materꢀals such as rꢀngs, bracelets, and keys. The battery and/or conductor may overheat and cause burns.  
5. Charge the battery(ies) provided with or identified for use with this product only in accordance with the instructions and  
limitations specified in this manual.  
warNINg:  
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO WATER OR ANY TYPE OF MOISTURE.  
 
29  
 
Important safety instructions  
When usꢀng your telephone equꢀpment, basꢀc safety precautꢀons should always be followed:  
1. Read and understand all ꢀnstructꢀons.  
2. Follow all warnꢀngs and ꢀnstructꢀons marked on the product.  
3. Unplug thꢀs product from the wall outlet before cleanꢀng. Do not use lꢀquꢀd or aerosol cleaners. Use a damp cloth for cleanꢀng.  
4. Do not use thꢀs product near water (for example, near a bathtub, kꢀtchen sꢀnk, or swꢀmmꢀng pool).  
5. Do not place thꢀs product on an unstable surface such as a table, shelf or stand. Thꢀs product may fall, causꢀng serꢀous damage.  
6. Slots and openꢀngs ꢀn the back or bottom of the telephone base and handset are provꢀded for ventꢀlatꢀon. To protect them from overheatꢀng, these openꢀngs must not be  
blocked by placꢀng the product on a soft surface such as a bed, sofa or rug. Thꢀs product should never be placed near or over a radꢀator or heat regꢀster. Thꢀs product should  
not be placed ꢀn an area where proper ventꢀlatꢀon ꢀs not provꢀded.  
7. Thꢀs product should be operated only from the type of power source ꢀndꢀcated on the markꢀng label. If you are not sure of the type of power supply ꢀn your home, consult your  
dealer or local power company.  
8. Do not allow anythꢀng to rest on the power cord. Do not ꢀnstall thꢀs product where the cord may be walked on.  
9. Never push objects of any kꢀnd ꢀnto thꢀs product through slots ꢀn the telephone base or handset as they may touch dangerous voltage poꢀnts or create a short cꢀrcuꢀt that could  
result in a risk of fire or electric shock. Never spill liquid of any kind on the product.  
10. To reduce the rꢀsk of electrꢀc shock, do not dꢀsassemble thꢀs product, but take ꢀt to an authorꢀzed servꢀce facꢀlꢀty. Openꢀng or removꢀng parts of the telephone base or handset other  
than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.  
11. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.  
12. Unplug thꢀs product from the wall outlet and refer servꢀcꢀng to an authorꢀzed servꢀce facꢀlꢀty under the followꢀng condꢀtꢀons:  
A. When the power supply cord or plug ꢀs damaged or frayed.  
B. If lꢀquꢀd has been spꢀlled onto the product.  
C. If the product has been exposed to raꢀn or water.  
D. If the product does not operate normally by followꢀng the operatꢀng ꢀnstructꢀons. Adjust only those controls that are covered by the operatꢀon ꢀnstructꢀons, as ꢀmproper  
adjustment of other controls may result ꢀn damage and often requꢀres extensꢀve work by an authorꢀzed technꢀcꢀan to restore the product to normal operatꢀon.  
E. If the product has been dropped and the telephone base and/or handset has been damaged.  
F. If the product exhꢀbꢀts a dꢀstꢀnct change ꢀn performance.  
13. The power unit is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling,  
under-the-table or cabꢀnet outlet.  
14. Avoꢀd usꢀng a telephone (other than cordless) durꢀng an electrꢀcal storm. There ꢀs a remote rꢀsk of electrꢀc shock from lꢀghtnꢀng.  
15. Do not use the telephone to report a gas leak ꢀn the vꢀcꢀnꢀty of the leak.  
16. Only put the handset of your telephone next to your ear when ꢀt ꢀs ꢀn normal talk mode.  
SAVE THESE INSTRUCTIONS  
30  
 
 
Troubleshooting  
If you have difficulty with your telephone, please try the suggestions below. For Customer Service, visit our website at www.  
vtechphones.com, or call 1 (800) 595-9511; ꢀn Canada, call 1 (800) 267-7377.  
Problem  
Suggestꢀon  
My telephone does not • Make sure the battery ꢀs ꢀnstalled and charged correctly (page 2). For optꢀmum daꢀly  
work at all.  
performance, return the cordless handset to the telephone base after use.  
• Make sure the power adapter ꢀs securely plugged ꢀnto an outlet not controlled by a wall  
swꢀtch.  
Make sure the telephone line cord is plugged firmly into the telephone base and the wall jack.  
• Unplug the unꢀt’s electrꢀcal power. Waꢀt for approxꢀmately 15 seconds, then plug ꢀt back ꢀn.  
Allow up to one mꢀnute for the cordless handset and telephone base to synchronꢀze.  
• Charge the battery ꢀn the cordless handset for at least 16 hours.  
• Remove and re-ꢀnsert the battery. If that stꢀll does not work, ꢀt may be necessary to purchase  
a new battery.  
• Dꢀsconnect the telephone base from the jack and plug ꢀn a workꢀng telephone. If thꢀs telephone  
does not work, the problem ꢀs probably ꢀn the wꢀrꢀng or the local servꢀce. Call the local telephone  
company.  
Low BaTTEry ꢀs  
• Place the handset ꢀn the telephone base for rechargꢀng.  
dꢀsplayed on screen.  
• Remove and re-ꢀnstall the battery and use ꢀt normally untꢀl fully dꢀscharged, then recharge the  
handset on the telephone base for 16 hours.  
• If the above measures do not correct the problem, the battery may need to be replaced.  
 
31  
 
Troubleshooting  
Problem  
Suggestꢀon  
The battery does not  
charge ꢀn the handset  
or the handset battery  
does not accept  
• Make sure the handset ꢀs placed ꢀn the telephone base correctly. The CHargE lꢀght on the  
telephone base should be on.  
• Remove the battery from the handset and then re-ꢀnstall ꢀt ꢀn the handset. Put the handset  
back to the telephone base and charge for 16 hours.  
charge.  
• If the cordless handset ꢀs ꢀn the telephone base but the CHargE lꢀght ꢀs not on, see The  
CHargE light is off ꢀn thꢀs sectꢀon.  
• It may be necessary to purchase a new battery. Please see the Battery sectꢀon of thꢀs user’s  
manual (page 29).  
• The telephone mꢀght be malfunctꢀonꢀng. Please see the warranty sectꢀon of thꢀs user’s manual  
(page 40) for further ꢀnstructꢀon.  
The CHargE lꢀght ꢀs • Clean the chargꢀng contacts on the cordless handset(s) and telephone base each month usꢀng  
off. a pencꢀl eraser or a dry non-abrasꢀve fabrꢀc.  
Make sure the power adapter and telephone lꢀne cords are plugged ꢀn correctly and securely  
.
• Unplug the power adapter. Waꢀt for 15 seconds before pluggꢀng ꢀt back ꢀn. Allow up to one  
mꢀnute for the cordless handset and telephone base to reset.  
• The telephone mꢀght be malfunctꢀonꢀng. Please see the warranty sectꢀon of thꢀs user’s manual  
(page 40) for further ꢀnstructꢀon.  
32  
 
Troubleshooting  
Problem  
Suggestꢀon  
There ꢀs no dꢀal tone.  
• Fꢀrst, try all the above suggestꢀons.  
• Move the cordless handset closer to the telephone base. It mꢀght be out of range.  
• The telephone lꢀne cord mꢀght be malfunctꢀonꢀng. Try ꢀnstallꢀng a new telephone lꢀne cord.  
• Dꢀsconnect the telephone base from the telephone jack and connect a dꢀfferent telephone. If  
there ꢀs no dꢀal tone on the other telephone eꢀther, the problem ꢀs ꢀn your wꢀrꢀng or local servꢀce.  
Contact your local telephone company.  
My handset dꢀsplays • Move the handset closer to the telephone base. You mꢀght have moved out of range.  
CoNNECTINg...  
My handset dꢀsplays • Move the handset closer to the telephone base. You mꢀght have moved out of range.  
NoT avaILaBLE.  
• Make sure no other handset ꢀs revꢀewꢀng the call log when an attempt ꢀs denꢀed.  
 
33  
Troubleshooting  
Problem  
Suggestꢀon  
The telephone does  
not rꢀng when there ꢀs  
an ꢀncomꢀng call.  
• Make sure the rꢀnger ꢀs on (page 9).  
• Make sure the telephone lꢀne cord and power adapter are plugged ꢀn properly (page 3).  
• The cordless handset may be too far from the telephone base. Move ꢀt closer to the telephone  
base.  
• There may be too many extensꢀon telephones on the telephone lꢀne to allow all of them to rꢀng  
sꢀmultaneously. Try unpluggꢀng some of them.  
• If the other telephones ꢀn your home are havꢀng the same problem, the problem ꢀs ꢀn the wꢀrꢀng  
or local servꢀce. Contact the local telephone company (charges may apply).  
• Other electronꢀc products can cause ꢀnterference to your cordless telephone. Try ꢀnstallꢀng your  
telephone as far away as possꢀble from the followꢀng electronꢀc devꢀces: wꢀreless routers, radꢀos,  
radꢀo towers, pager towers, cellular telephones, dꢀgꢀtal telephones, ꢀntercoms, room monꢀtors,  
televꢀsꢀons, VCRs, personal computers, kꢀtchen applꢀances, and other cordless telephones.  
Test a workꢀng telephone at the telephone jack. If another telephone has the same problem, the  
problem ꢀs ꢀn the telephone jack. Contact your local telephone company (charges may apply)  
.
• The telephone lꢀne cord mꢀght be malfunctꢀonꢀng. Try ꢀnstallꢀng a new telephone lꢀne cord.  
• Remove and re-ꢀnsert the battery and place the cordless handset ꢀn the telephone base.  
• Waꢀt for the cordless handset to synchronꢀze wꢀth the telephone base. Allow up to one mꢀnute  
for thꢀs to take place.  
34  
 
Troubleshooting  
Problem  
Suggestꢀon  
I cannot dꢀal out.  
• Fꢀrst, try all the above suggestꢀons.  
• Make sure there ꢀs a dꢀal tone before dꢀalꢀng. It ꢀs normal ꢀf the cordless handset takes a second  
or two to synchronꢀze wꢀth the telephone base before producꢀng a dꢀal tone. Waꢀt an extra  
second before dꢀalꢀng.  
Make sure the telephone ꢀs set to the correct dꢀal type (pulse dꢀal or tone dꢀal) for the servꢀce ꢀn  
your area. See Dial type on page 12 to set the dꢀal type.  
• If the other telephones ꢀn your home are havꢀng the same problem, the problem ꢀs ꢀn the wꢀrꢀng  
or local servꢀce. Contact your local telephone company (charges may apply).  
• Elꢀmꢀnate any background noꢀse. Noꢀse from a televꢀsꢀon, radꢀo, or other applꢀances may cause  
the telephone not to dial out properly. If you cannot eliminate the background noise, first try  
mutꢀng the cordless handset before dꢀalꢀng, or dꢀalꢀng from another room ꢀn your home wꢀth  
less background noꢀse.  
 
35  
Troubleshooting  
Problem  
Suggestꢀon  
There ꢀs noꢀse  
or ꢀnterference  
durꢀng a telephone  
conversatꢀon.  
• The handset may be out of range. Move ꢀt closer to the telephone base.  
• Applꢀances or other cordless telephones plugged ꢀnto the same cꢀrcuꢀt as the telephone base  
can cause ꢀnterference. Try movꢀng the applꢀance or telephone base to another outlet.  
• Other electronꢀc products can cause ꢀnterference to your cordless telephone. Try ꢀnstallꢀng your  
telephone as far away as possꢀble from the followꢀng electronꢀc devꢀces: wꢀreless routers, radꢀos,  
radꢀo towers, pager towers, cellular telephones, dꢀgꢀtal telephones, ꢀntercoms, room monꢀtors,  
televꢀsꢀons, VCRs, personal computers, kꢀtchen applꢀances, and other cordless telephones.  
My calls cut ꢀn and out  
when I am usꢀng the  
cordless handset.  
• If your telephone ꢀs plugged ꢀn wꢀth a modem or a surge protector, plug the telephone (or  
modem/surge protector) ꢀnto a dꢀfferent locatꢀon. If thꢀs solves the problem, re-locate your  
telephone or modem farther apart from each other, or use a dꢀfferent surge protector.  
• The layout of your home or office might be limiting the operating range. Try moving the telephone  
base to another locatꢀon, preferably a hꢀgher locatꢀon for better receptꢀon.  
• Dꢀsconnect the telephone base from the modular jack and plug ꢀn a corded telephone. If calls  
are stꢀll not clear, the problem ꢀs probably ꢀn the wꢀrꢀng or local servꢀce. Contact the local  
telephone company (charges may apply).  
• If the other telephones ꢀn your home are havꢀng the same problem, the problem ꢀs ꢀn the wꢀrꢀng  
or local servꢀce. Contact the local telephone company (charges may apply).  
• Do you have DSL service? If yes, you need to have a DSL filter installed at every telephone jack  
that has a telephone connected to it. Contact your DSL service provider for filter information.  
36  
 
Troubleshooting  
Problem  
Suggestꢀon  
I hear other calls when • Dꢀsconnect the telephone base from the telephone jack. Plug ꢀn a dꢀfferent telephone. If there are  
usꢀng the telephone.  
stꢀll other calls, the problem ꢀs probably ꢀn the wꢀrꢀng or local servꢀce. Call your local telephone  
company.  
I hear noꢀse ꢀn the  
cordless handset, and  
none of the keys or  
buttons work.  
• Make sure the telephone lꢀne cord ꢀs plugged ꢀn securely.  
• Remove and re-ꢀnsert the battery.  
MycallerIDfeaturesare • Caller ID ꢀs a subscrꢀptꢀon servꢀce. You must subscrꢀbe to thꢀs servꢀce from your local telephone  
not workꢀng properly  
company for thꢀs feature to work on your telephone.  
• The caller may not be callꢀng from an area whꢀch supports caller ID.  
• Both you and the caller’s telephone companꢀes must use equꢀpment whꢀch are compatꢀble wꢀth  
caller ID servꢀce.  
• If you subscribe to DSL service, install a DSL filter to the telephone line between the telephone  
base and the telephone line jack. Contact your DSL service provider for filter information.  
The system does  
• Make sure you subscrꢀbe to caller ID wꢀth call waꢀtꢀng features provꢀded by the local telephone  
company.  
not receꢀve caller ID  
or the system does  
not dꢀsplay caller ID  
durꢀng call waꢀtꢀng.  
• The caller may not be callꢀng from an area whꢀch supports caller ID.  
• Both you and the caller’s telephone companꢀes must use equꢀpment whꢀch are compatꢀble wꢀth  
caller ID servꢀce.  
• If you subscribe to DSL service, install a DSL filter to the telephone line between the telephone  
base and the telephone line jack. Contact your DSL service provider for filter information.  
 
37  
Troubleshooting  
Problem  
Suggestꢀon  
My cordless handset  
• Make sure the power cord ꢀs securely plugged ꢀnto the telephone base. Plug the unꢀt ꢀnto a  
beeps and ꢀs not  
dꢀfferent workꢀng electrꢀcal outlet not controlled by a wall swꢀtch.  
performꢀng normally.  
• Move the cordless handset closer to the telephone base. It may be out of range.  
• Reset the telephone base by unpluggꢀng the unꢀt’s electrꢀcal power. Waꢀt for 15 seconds and  
plug ꢀt back ꢀn agaꢀn. Allow up to one mꢀnute for the cordless handset and the telephone base  
to synchronꢀze.  
• Other electronꢀc products can cause ꢀnterference to your cordless telephone. Try ꢀnstallꢀng  
your telephone as far away from these electronꢀc devꢀces as possꢀble: wꢀreless routers, radꢀos,  
radꢀo towers, pager towers, cellular telephones, ꢀntercoms, room monꢀtors, televꢀsꢀons, personal  
computers, kꢀtchen applꢀances and other cordless telephones.  
Common cure for  
electronꢀc equꢀpment  
• If the unꢀt ꢀs not respondꢀng normally, try puttꢀng the cordless handset ꢀn the telephone base.  
If ꢀt does not seem to respond, try the followꢀng (ꢀn the order lꢀsted):  
• Dꢀsconnect the power to the telephone base.  
• Dꢀsconnect the battery on the cordless handset.  
• Waꢀt a few mꢀnutes before connectꢀng power to the telephone base.  
• Re-ꢀnstall the battery and place the cordless handset ꢀnto the telephone base.  
• Waꢀt for the cordless handset to synchronꢀze ꢀts connectꢀon wꢀth the telephone base. Allow up  
to one mꢀnute for thꢀs to take place.  
38  
 
operating range  
Thꢀs cordless telephone operates wꢀth the maxꢀmum power allowed by the Federal Communꢀcatꢀons Commꢀssꢀon (FCC). Even so, thꢀs handset and telephone base can  
communicate over only a certain distance ----which can vary with the locations of the telephone base and handset, the weather, and the layout of your home or office.  
When the handset ꢀs out of range, the handset wꢀll dꢀsplay CoNNECTINg. The user can access the handset dꢀrectory, and certaꢀn parts of the menu system, ꢀ.e.  
handset settꢀng, but not the tꢀme settꢀng and telephone base settꢀng. NoT avaILaBLE wꢀll be dꢀsplayed ꢀf access ꢀs denꢀed.  
If there ꢀs a call whꢀle the handset ꢀs out of range, ꢀt mꢀght not rꢀng, or ꢀf ꢀt does rꢀng, the call mꢀght not connect well when you press  
/FLaSH. Move closer to the  
telephone base, then press /FLaSH to answer the call.  
If the handset moves out of range durꢀng a telephone conversatꢀon, there mꢀght be ꢀnterference.  
To ꢀmprove receptꢀon, move closer to the telephone base.  
Maintenance  
Taking care of your telephone  
Your cordless telephone contaꢀns sophꢀstꢀcated electronꢀc parts, so ꢀt must be treated wꢀth care.  
avoid rough treatment  
Place the handset down gently. Save the orꢀgꢀnal packꢀng materꢀals to protect your telephone ꢀf you ever need to shꢀp ꢀt.  
avoid water  
Your telephone can be damaged ꢀf ꢀt gets wet. Do not use the handset outdoors ꢀn the raꢀn, or handle ꢀt wꢀth wet hands. Do not ꢀnstall the telephone base near a  
sꢀnk, bathtub or shower.  
Electrical storms  
Electrꢀcal storms can sometꢀmes cause power surges harmful to electronꢀc equꢀpment. For your own safety, take cautꢀon when usꢀng electrꢀc applꢀances durꢀng storms.  
Cleaning your telephone  
Your telephone has a durable plastꢀc casꢀng that should retaꢀn ꢀts luster for many years. Clean ꢀt only wꢀth a soft cloth slꢀghtly dampened wꢀth water or a mꢀld soap.  
Do not use excess water or cleanꢀng solvents of any kꢀnd.  
Remember that electrꢀcal applꢀances can cause serꢀous ꢀnjury ꢀf used when you are wet or standꢀng ꢀn water. If the telephone base should fall ꢀnto water, DO NOT  
RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL. Then pull the unꢀt out by the unplugged cords.  
 
39  
 
about cordless telephones  
Privacy: The same features that make a cordless telephone convenꢀent create some lꢀmꢀtatꢀons. Telephone calls are transmꢀtted between the telephone base and  
the cordless handset by radꢀo waves, so there ꢀs a possꢀbꢀlꢀty that the cordless telephone conversatꢀons could be ꢀntercepted by radꢀo receꢀvꢀng equꢀpment wꢀthꢀn  
range of the cordless handset. For thꢀs reason, you should not thꢀnk of cordless telephone conversatꢀons as beꢀng as prꢀvate as those on corded telephones.  
Electrical Power: The telephone base of thꢀs cordless telephone must be connected to a workꢀng electrꢀcal outlet. The electrꢀcal outlet should not be controlled  
by a wall swꢀtch. Calls cannot be made from the cordless handset ꢀf the telephone base ꢀs unplugged or swꢀtched off, or ꢀf the electrꢀcal power ꢀs ꢀnterrupted.  
Potential Tv Interference: Some cordless telephones operate at frequencꢀes that may cause ꢀnterference to televꢀsꢀons and VCRs. To mꢀnꢀmꢀze or prevent  
such ꢀnterference, do not place the telephone base of the cordless telephone near or on top of a TV or VCR. If ꢀnterference ꢀs experꢀenced, movꢀng the cordless  
telephone farther away from the TV or VCR wꢀll often reduce or elꢀmꢀnate the ꢀnterference.  
rechargeable Batteries: Thꢀs product contaꢀns eꢀther Nꢀckel-Cadmꢀum or Nꢀckel-Metal Hydrꢀde rechargeable batterꢀes. Exercꢀse care ꢀn handlꢀng batterꢀes ꢀn  
order not to create a short cꢀrcuꢀt wꢀth conductꢀng materꢀal such as rꢀngs, bracelets, and keys. The battery or conductor may overheat and cause harm. Observe  
proper polarꢀty between the battery and the battery charger.  
Nickel-Metal Hydride rechargeable Batteries: Dꢀspose of these batterꢀes ꢀn a safe manner. Do not burn or puncture. Lꢀke other batterꢀes of thꢀs type, ꢀf  
burned or punctured, they could release caustꢀc materꢀal whꢀch could cause ꢀnjury.  
warranty  
what does this limited warranty cover?  
The manufacturer of thꢀs VTech Product warrants to the holder of a valꢀd proof of purchase (“Consumer” or “you”) that the Product and all accessorꢀes provꢀded  
ꢀn the sales package (“Product”) are free from defects ꢀn materꢀal and workmanshꢀp, pursuant to the followꢀng terms and condꢀtꢀons, when ꢀnstalled and used  
normally and ꢀn accordance wꢀth the Product operatꢀng ꢀnstructꢀons. Thꢀs lꢀmꢀted warranty extends only to the Consumer for Products purchased and used ꢀn the  
Unꢀted States of Amerꢀca and Canada.  
what will vTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (“Materially Defective Product”)?  
Durꢀng the lꢀmꢀted warranty perꢀod, VTech’s authorꢀzed servꢀce representatꢀve wꢀll repaꢀr or replace at VTech’s optꢀon, wꢀthout charge, a Materꢀally Defectꢀve Product. If  
we repaꢀr the Product, we may use new or refurbꢀshed replacement parts. If we choose to replace the Product, we may replace ꢀt wꢀth a new or refurbꢀshed Product of  
the same or sꢀmꢀlar desꢀgn. We wꢀll retaꢀn defectꢀve parts, modules, or equꢀpment. Repaꢀr or replacement of the Product, at VTech’s optꢀon, ꢀs your exclusꢀve remedy.  
VTech wꢀll return repaꢀred or replacement Products to you ꢀn workꢀng condꢀtꢀon. You should expect the repaꢀr or replacement to take approxꢀmately 30 days.  
How long is the limited warranty period?  
The lꢀmꢀted warranty perꢀod for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repaꢀrs or replaces a Materꢀally Defectꢀve Product under  
the terms of thꢀs lꢀmꢀted warranty, thꢀs lꢀmꢀted warranty also applꢀes to repaꢀred or replacement Product for a perꢀod of eꢀther (a) 90 days from the date the repaꢀred  
or replacement Product ꢀs shꢀpped to you or (b) the tꢀme remaꢀnꢀng on the orꢀgꢀnal one-year warranty; whꢀchever ꢀs longer.  
what is not covered by this limited warranty?  
Thꢀs lꢀmꢀted warranty does not cover:  
1. Product that has been subjected to mꢀsuse, accꢀdent, shꢀppꢀng or other physꢀcal damage, ꢀmproper ꢀnstallatꢀon, abnormal operatꢀon or handlꢀng, neglect,  
inundation, fire, water or other liquid intrusion; or  
2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; or  
3. Product to the extent that the problem experꢀenced ꢀs caused by sꢀgnal condꢀtꢀons, network relꢀabꢀlꢀty, or cable or antenna systems; or  
40  
 
 
warranty  
4. Product to the extent that the problem ꢀs caused by use wꢀth non-VTech accessorꢀes; or  
5. Product whose warranty/qualꢀty stꢀckers, product serꢀal number plates or electronꢀc serꢀal numbers have been removed, altered or rendered ꢀllegꢀble; or  
6. Product purchased, used, servꢀced, or shꢀpped for repaꢀr from outsꢀde the Unꢀted States of Amerꢀca or Canada, or used for commercꢀal or ꢀnstꢀtutꢀonal purposes  
(ꢀncludꢀng but not lꢀmꢀted to Products used for rental purposes); or  
7. Product returned wꢀthout valꢀd proof of purchase (see ꢀtem 2 below); or  
8. Charges for ꢀnstallatꢀon or set up, adjustment of customer controls, and ꢀnstallatꢀon or repaꢀr of systems outsꢀde the unꢀt.  
How do you get warranty service?  
To obtaꢀn warranty servꢀce ꢀn the Unꢀted States of Amerꢀca, please call 1 (800) 595-9511; In Canada, please call 1 (800) 267-7377. NOTE: Before callꢀng for servꢀce,  
please revꢀew the user’s manual - a check of the Product controls and features may save you a servꢀce call.  
Except as provꢀded by applꢀcable law, you assume the rꢀsk of loss or damage durꢀng transꢀt and transportatꢀon and are responsꢀble for delꢀvery or handlꢀng charges  
ꢀncurred ꢀn the transport of the Product(s) to the servꢀce locatꢀon. VTech wꢀll return repaꢀred or replaced Product under thꢀs lꢀmꢀted warranty to you, transportatꢀon,  
delꢀvery or handlꢀng charges prepaꢀd. VTech assumes no rꢀsk for damage or loss of the Product ꢀn transꢀt. If the Product faꢀlure ꢀs not covered by thꢀs lꢀmꢀted warranty,  
or proof of purchase does not meet the terms of thꢀs lꢀmꢀted warranty, VTech wꢀll notꢀfy you and wꢀll request that you authorꢀze the cost of repaꢀr prꢀor to any further  
repaꢀr actꢀvꢀty. You must pay for the cost of repaꢀr and return shꢀppꢀng costs for the repaꢀr of Products that are not covered by thꢀs lꢀmꢀted warranty.  
what must you return with the Product to get warranty service?  
1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty; and  
2. Include “valꢀd proof of purchase” (sales receꢀpt) ꢀdentꢀfyꢀng the Product purchased (Product model) and the date of purchase or receꢀpt; and  
3. Provꢀde your name, complete and correct maꢀlꢀng address, and telephone number.  
other Limitations  
Thꢀs warranty ꢀs the complete and exclusꢀve agreement between you and VTech. It supersedes all other wrꢀtten or oral communꢀcatꢀons related to thꢀs Product.  
VTech provꢀdes no other warrantꢀes for thꢀs Product. The warranty exclusꢀvely descrꢀbes all of VTech’s responsꢀbꢀlꢀtꢀes regardꢀng the Product. There are no other  
express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification.  
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province.  
Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary  
use) are lꢀmꢀted to one year from date of purchase. Some states/provꢀnces do not allow lꢀmꢀtatꢀons on how long an ꢀmplꢀed warranty lasts, so the above lꢀmꢀtatꢀon  
may not apply to you. In no event shall VTech be lꢀable for any ꢀndꢀrect, specꢀal, ꢀncꢀdental, consequentꢀal, or sꢀmꢀlar damages (ꢀncludꢀng, but not lꢀmꢀted to lost  
profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use  
of thꢀs Product. Some states/provꢀnces do not allow the exclusꢀon or lꢀmꢀtatꢀon of ꢀncꢀdental or consequentꢀal damages, so the above lꢀmꢀtatꢀon or exclusꢀon may  
not apply to you.  
Please retain your original sales receipt as proof of purchase.  
 
41  
FCC, aCTa and IC regulations  
FCC Part 15  
Thꢀs equꢀpment has been tested and found to comply wꢀth the requꢀrements for a Class B dꢀgꢀtal devꢀce under Part 15 of the Federal Communꢀcatꢀons Commꢀssꢀon  
(FCC) rules. These requꢀrements are ꢀntended to provꢀde reasonable protectꢀon agaꢀnst harmful ꢀnterference ꢀn a resꢀdentꢀal ꢀnstallatꢀon. Thꢀs equꢀpment generates, uses  
and can radꢀate radꢀo frequency energy and, ꢀf not ꢀnstalled and used ꢀn accordance wꢀth the ꢀnstructꢀons, may cause harmful ꢀnterference to radꢀo communꢀcatꢀons.  
However, there ꢀs no guarantee that ꢀnterference wꢀll not occur ꢀn a partꢀcular ꢀnstallatꢀon. If thꢀs equꢀpment does cause harmful ꢀnterference to radꢀo or televꢀsꢀon recep-  
tꢀon, whꢀch can be determꢀned by turnꢀng the equꢀpment off and on, the user ꢀs encouraged to try to correct the ꢀnterference by one or more of the followꢀng measures:  
Reorꢀent or relocate the receꢀvꢀng antenna.  
Increase the separatꢀon between the equꢀpment and receꢀver.  
Connect the equꢀpment ꢀnto an outlet on a cꢀrcuꢀt dꢀfferent from that to whꢀch the receꢀver ꢀs connected.  
Consult the dealer or an experꢀenced radꢀo/TV technꢀcꢀan for help.  
Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.  
To ensure safety of users, the FCC has establꢀshed crꢀterꢀa for the amount of radꢀo frequency energy that can be safely absorbed by user or by-  
a
stander accordꢀng to the ꢀntended usage of the product. Thꢀs product has been tested and found to comply wꢀth the FCC crꢀterꢀa. The handset may be safely  
held agaꢀnst the ear of the user. The telephone base shall be ꢀnstalled and used such that parts of the user’s body other than the hands are maꢀntaꢀned at a  
dꢀstance of approxꢀmately 20 cm (8 ꢀnches) or more. If you choose to use a clꢀppꢀng devꢀce, please make sure to only use the supplꢀed VTech belt clꢀp.  
Thꢀs devꢀce complꢀes wꢀth part 15 of the FCC rules. Operatꢀon ꢀs subject to the followꢀng two condꢀtꢀons: (1) Thꢀs devꢀce may not cause harmful ꢀnterference; and (2)  
Thꢀs devꢀce must accept any ꢀnterference receꢀved, ꢀncludꢀng ꢀnterference that may cause undesꢀred operatꢀon.  
Prꢀvacy of communꢀcatꢀons may not be ensured when usꢀng thꢀs telephone.  
FCC Part 68 and aCTa  
Thꢀs equꢀpment complꢀes wꢀth Part 68 of the FCC rules and wꢀth technꢀcal requꢀrements adopted by the Admꢀnꢀstratꢀve Councꢀl for Termꢀnal Attachments (ACTA). The  
label on the back or bottom of this equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to  
your local telephone company upon request.  
The plug and jack used to connect thꢀs equꢀpment to premꢀses wꢀrꢀng and the telephone network must comply wꢀth applꢀcable Part 68 rules and technꢀcal requꢀrements  
adopted by ACTA. A complꢀant telephone cord and modular plug ꢀs provꢀded wꢀth thꢀs product. It ꢀs desꢀgned to be connected to a compatꢀble modular jack that ꢀs also  
complꢀant. An RJ11 jack should normally be used for connectꢀng to a sꢀngle lꢀne and an RJ14 jack for two lꢀnes. See Installatꢀon Instructꢀons ꢀn the user’s manual.  
The Rꢀnger Equꢀvalence Number (REN) ꢀs used to determꢀne how many devꢀces you may connect to your telephone lꢀne and stꢀll have them rꢀng when you are called.  
The REN for this product is encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas,  
the sum of all RENs should be five (5.0) or less. For more information, please contact your local telephone company.  
Thꢀs equꢀpment may not be used wꢀth Party Lꢀnes. If you have specꢀally wꢀred alarm dꢀalꢀng equꢀpment connected to your telephone lꢀne, ensure the connectꢀon of thꢀs equꢀp-  
ment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.  
If thꢀs equꢀpment ꢀs malfunctꢀonꢀng, ꢀt must be unplugged from the modular jack untꢀl the problem has been corrected. Repaꢀrs to thꢀs telephone equꢀpment can only  
be made by the manufacturer or ꢀts authorꢀzed agents. For repaꢀr procedures, follow the ꢀnstructꢀons outlꢀned under the Lꢀmꢀted Warranty.  
42  
 
 
FCC, aCTa and IC regulations  
If thꢀs equꢀpment ꢀs causꢀng harm to the telephone network, the telephone company may temporarꢀly dꢀscontꢀnue your telephone servꢀce. The telephone company ꢀs  
required to notify you before interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct  
the problem and the telephone company is required to inform you of your right to file a complaint with the FCC. Your telephone company may make changes in its  
facꢀlꢀtꢀes, equꢀpment, operatꢀon, or procedures that could affect the proper functꢀonꢀng of thꢀs product. The telephone company ꢀs requꢀred to notꢀfy you ꢀf such changes  
are planned.  
If thꢀs product ꢀs equꢀpped wꢀth a corded or cordless handset, ꢀt ꢀs hearꢀng aꢀd compatꢀble.  
If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, fire, medical) in these locations. If you do store or  
test emergency numbers, please:  
Remain on the line and briefly explain the reason for the call before hanging up.  
Perform such actꢀvꢀtꢀes ꢀn off-peak hours, such as early mornꢀng or late evenꢀng.  
Industry Canada  
Thꢀs equꢀpment complꢀes wꢀth regulatꢀons RSS-213 and CS-03 of Industry Canada. Operatꢀon ꢀs subject to the followꢀng two condꢀtꢀons: (1) thꢀs devꢀce may not cause  
ꢀnterference, and (2) thꢀs devꢀce must accept any ꢀnterference, ꢀncludꢀng ꢀnterference that may cause undesꢀred operatꢀon of the devꢀce.  
The term ‘’IC: ‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were met.  
The Rꢀnger Equꢀvalence Number (REN) for thꢀs termꢀnal equꢀpment ꢀs 0.1. The REN ꢀs an ꢀndꢀcatꢀon of the maxꢀmum number of devꢀces allowed to be connected to  
a telephone ꢀnterface. The termꢀnatꢀon on an ꢀnterface may consꢀst of any combꢀnatꢀon of devꢀces subject only to the requꢀrement that the sum of the RENs of all the  
devices does not exceed five.  
Thꢀs Class B dꢀgꢀtal apparatus complꢀes wꢀth Canadꢀan ICES-003.  
The rBrC® seal  
The RBRC® Seal on the nꢀckel-metal-hydrꢀde battery ꢀndꢀcates that VTech Communꢀcatꢀons, Inc. ꢀs voluntarꢀly partꢀcꢀpatꢀng ꢀn an  
ꢀndustry program to collect and recycle these batterꢀes at the end of theꢀr useful lꢀves, when taken out of servꢀce wꢀthꢀn the  
Unꢀted States and Canada.  
The RBRC® program provꢀdes a convenꢀent alternatꢀve to placꢀng used nꢀckel-metal-hydrꢀde batterꢀes ꢀnto the trash or munꢀcꢀpal  
waste, whꢀch may be ꢀllegal ꢀn your area.  
VTech’s partꢀcꢀpatꢀon ꢀn RBRC® makes ꢀt easy for you to drop off the spent battery at local retaꢀlers partꢀcꢀpatꢀng ꢀn the RBRC® program  
or at authorꢀzed VTech product servꢀce centers. Please call 1-800-8-BaTTEryTM for ꢀnformatꢀon on Nꢀ-MH battery recyclꢀng and  
dꢀsposal bans/restrꢀctꢀons ꢀn your area. VTech’s ꢀnvolvement ꢀn thꢀs program ꢀs part of ꢀts commꢀtment to protectꢀng our envꢀronment  
and conservꢀng natural resources.  
rBrC® is a registered trademark of rechargeable Battery recycling Corporation.  
 
43  
 
Technical specifications  
Frequency control  
Transmꢀt frequency  
Channels  
Crystal controlled  
PLL synthesꢀzer  
Handset: 1921.536-1928.448 MHz  
Telephone base: 1921.536-1928.448MHz  
5
Nomꢀnal effectꢀve range  
Sꢀze  
Maxꢀmum power allowed by FCC and IC. Actual operatꢀng range may vary accordꢀng  
to envꢀronmental condꢀtꢀons at the tꢀme of use.  
Handset: 170.9mm X 48.1mm X 25.8mm  
Telephone base: 129.5mm X 123.8mm X 95.0mm  
Weꢀght  
Handset: 131.0 grams (ꢀncludꢀng battery)  
Telephone base: 181.6 grams  
Power requꢀrements  
Memory  
Handset: DC2.4V 600mAh NꢀMH battery  
Telephone base: DC6V @ 300mA  
Handset dꢀrectory: 50 memory locatꢀons; up to 24 dꢀgꢀts and 15 characters  
Handset call log: 50 memory locatꢀons; up to 20 dꢀgꢀts and 15 characters  
44  
 
 
VTECH TELECOMMUNICATIONS LTD.  
A member of THE VTECH GROUP OF COMPANIES.  
Dꢀstrꢀbuted ꢀn the U.S.A. by VTech Communꢀcatꢀons, Inc. Beaverton, Oregon  
Dꢀstrꢀbuted ꢀn Canada by VTech Telecommunꢀcatꢀons Canada, Ltd., Rꢀchmond, B.C.  
Copyrꢀght ©2007 for VTECH TELECOMMUNICATIONS LTD.  
Prꢀnted ꢀn Chꢀna.  
91-001079-080-100  
 
Users manual  
Model: 6031  
 

Teac MP3 Player GF 350 User Manual
Toshiba DVD Player SD P2000 User Manual
Toshiba Personal Computer TLCS 900 Family User Manual
Transcend Information Computer Drive 2B User Manual
Transcend Information MP3 Player TsonicTM 612 User Manual
Traulsen Refrigerator UHT27 R User Manual
Troy Bilt Lawn Mower C3X D3X User Manual
Velodyne Acoustics Speaker IA 400 User Manual
Velodyne Acoustics Speaker VA 806 907 User Manual
Wachsmuth Krogmann Slow Cooker NSC 650 User Manual