VTech Cordless Telephone DS6101 User Manual

User’s manual  
Accessory handset  
for use with  
VTech model DS6151  
w w w.v techphones.com  
Model: DS6101  
BC  
 
Getting started  
Parts checklist  
Your telephone contains the following items. Save your sales receipt and  
original packaging in the event warranty service is necessary.  
Battery compartment cover  
Battery  
Belt clip  
User’s manual  
Charger and power adapter  
Handset  
To purchase a replacement battery or a power adapter, visit our website at  
 
1
 
Getting started  
Battery installation  
Install the battery as shown below.  
1 Plug the battery connector  
securely into the socket inside the  
battery compartment, matching  
the color-coded label.  
2 Place the battery with the label  
THIS SIDE UP and the wires  
inside the battery compartment.  
Slide the battery compartment  
cover towards the center of the  
handset until it clicks into place.  
Charge the handset by placing it  
in the telephone base.  
3
4
CHARGE light remains  
on when charging.  
Battery.charging  
Once you have installed the battery, the screen indicates the battery status  
(see the table below).  
For best performance, keep the handset in the telephone base or  
charger when not in use.  
The battery is fully charged after 16 hours of continuous charging.  
If the handset will not be used for a long time, disconnect and  
remove the battery to prevent any possible leakage.  
Battery indicators  
Battery status  
Action  
The screen is blank.  
Battery has no charge and  
the handset cannot be used.  
Charge without interruption  
(at least 30 minutes).  
The screen shows  
Battery has very little charge Charge without interruption  
Place.handset.in.  
and the handset cannot be  
(at least 30 minutes).  
charger.and flashes. used.  
Battery has enough charge  
to be used for a short time.  
Charge without interruption  
(at least 30 minutes).  
The screen shows Low.  
battery and flashes.  
The screen shows  
HANDSET.  
Battery is charged.  
To keep the battery charged,  
place it in the telephone  
base when not in use.  
 
2
 
Getting started  
Battery.charging  
When.the.battery.is.fully.charged,.you.can.expect.the.following.performance:  
Operation  
Operating time  
Up to 10 hours  
Up to 7 hours  
Up to 10 days  
While in handset use (talking*)  
While in speakerphone mode (talking*)  
While not in use (standby**)  
*Operating times vary depending on your actual use and the age of the battery.  
**Handset is not charging or in use.  
 
3
Getting started  
Belt clip and optional headset  
Belt clip  
To attach the belt clip:  
To remove the belt clip:  
Snap the belt clip into  
the slots on both sides  
of the handset.  
Gently lift either of the  
belt clip tabs outwards to  
remove the belt clip from  
the handset.  
Headset  
For handsfree telephone conversation, you can use any industry standard  
2.5mm headset (purchased separately). For best results, use a  
VTech 2.5mm headset.  
Lift the plastic cover.  
Plug a 2.5mm headset  
into the jack on the side  
of the handset.  
 
4
 
Getting started  
Add and register a handset  
Each newly purchased handset (DS6101) must be registered to the  
telephone base (DS6151) before use. When first purchased, each  
expansion handset shows Press [HOLD] on base for 4 sec, then press [#]  
on handset. You may need to charge the handset before registering to the  
telephone base. For more details on battery charging, see the table on  
page 2.  
To make registration easier, read all of the instructions on this page before  
you begin.  
To register a handset:  
1. Place the unregistered handset in the telephone base. If Press [HOLD]  
on base for 4 sec, then press [#] on handset does not appear on the  
handset screen after a few seconds, remove the handset and place it in  
the telephone base again.  
2. Press and hold HOLD on the telephone base for about four seconds until  
the telephone base displays Registering handset. While the handset  
is still in the telephone base, press (pound key) on the handset. The  
#
handset shows Registering... Please wait and it takes up to 60 seconds  
to complete the registration. The handset and the telephone base show  
HANDSET X Registered (X represents the handset number assigned)  
and you hear a beep when the registration completes.  
When the registration is complete, the newly registered handset is assigned  
the next available handset registration number. For instance, if you already  
have HANDSET, the next registered handset will be HANDSET 2. Then your  
first handset will be renamed as HANDSET 1.  
#
HOLD  
• If the registration fails, the handset shows Registration failed. To reset the  
handset, remove the handset from the telephone base and place it back in.  
Try the registration process again.  
• You cannot register a handset if any other system handset is in use.  
• Only one handset can be registered at a time.  
 
5
 
Getting started  
Replace a handset  
If you want to replace a handset or reassign the designated handset number  
of a registered handset, you must deregister all the handsets and then  
individually register each handset.  
To make deregistration easier, read all of the instructions on this page before  
you begin.  
To deregister all handsets:  
1. Remove any handset from the telephone base. Press and hold HOLD on  
the telephone base for about 10 seconds until the telephone base displays  
Deregister all handsets?  
2. Press the YES softkey.  
3. The deregistration process takes about 10 seconds to complete. All  
handsets show Press [HOLD] on base for 4 sec, then press [#] on  
handset when the deregistration completes.  
If deregistration fails, you may need to reset the telephone and try again.  
To reset:  
1. Pick up the registered handset and then press  
or  
.
2. Press OFF and then place the handset back in the telephone base.  
-OR-  
1. Unplug the power adapter from the telephone base, then plug it back in.  
You cannot deregister a handset if any system handset or telephone base is  
in use.  
 
6
 
Getting started  
Handset layout  
Softkeys (2)  
Press to select a menu item displayed above the key.  
(speakerphone)  
Press to make or join a call using the first available  
line, starting with line 1.  
Press to answer a call.  
During a call, press to switch between speakerphone  
and handset use.  
/VOL (directory/volume)  
Press to enter the directory when the telephone is  
not in use.  
While in a menu, press to scroll up.  
During a call or message playback, press to increase  
the listening volume.  
(line 1/flash)  
Press to make or answer a call on line 1.  
During a call, press to receive an incoming call on  
line 1 when you receive a call waiting alert.  
CID /VOL (caller ID/volume)  
Press to review the call log when the telephone is  
not in use.  
While in a menu, press to scroll down.  
During a call or message playback, press to  
decrease the listening volume.  
1
While reviewing a call log entry, press repeatedly to  
add or remove 1 in front of the telephone number  
before dialing or saving it in the directory.  
TONE  
Press to switch to tone dialing temporarily when  
using the pulse service.  
REDIAL/PAUSE  
Press to review the redial list.  
While dialing or entering numbers into the directory,  
press and hold to insert a dialing pause.  
 
7
 
Getting started  
Handset layout (continued)  
Headset jack  
Plug in a wired headset for handsfree telephone  
conversation.  
CHARGE light  
On when the handset is charging in the telephone  
base.  
OFF  
During a call, press to hang up.  
Press and hold while the telephone is not in use to  
erase the missed calls indicator.  
Press to delete a digit or character while entering a  
number or name.  
While in a menu, press to return to the previous  
menu or press and hold to return to the idle mode.  
(line 2/flash)  
Press to make or answer a call on line 2.  
During a call, press to receive an incoming call on  
line 2 when you receive a call waiting alert  
.
#
Press repeatedly to show other dialing options when  
reviewing a call log entry.  
INT (intercom)  
Press to initiate an intercom conversation or transfer  
a call.  
HOLD  
Press to put a call on hold.  
 
8
Appendix  
Important safety instructions  
When using your telephone equipment, basic safety precautions should always be followed to  
reduce the risk of fire, electric shock and injury, including the following:  
1. Read and understand all instructions.  
2. Follow all warnings and instructions marked on the product.  
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners.  
Use a damp cloth for cleaning.  
4. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry  
tub or swimming pool, or in a wet basement or shower.  
5. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.  
6. Avoid placing the telephone system in places with extreme temperature, direct sunlight, or  
other electrical devices. Protect your phone from moisture, dust, corrosive liquids and fumes.  
7. Slots and openings in the back or bottom of the telephone base and handset are provided for  
ventilation. To protect them from overheating, these openings must not be blocked by placing  
the product on a soft surface such as a bed, sofa or rug. This product should never be placed  
near or over a radiator or heat register. This product should not be placed in any area where  
proper ventilation is not provided.  
8. This product should be operated only from the type of power source indicated on the marking  
label. If you are not sure of the type of power supply in your home or office, consult your dealer  
or local power company.  
9. Do not allow anything to rest on the power cord. Do not install this product where the cord may  
be walked on.  
10. Never push objects of any kind into this product through the slots in the telephone base or  
handset because they may touch dangerous voltage points or create a short circuit. Never spill  
liquid of any kind on the product.  
11. To reduce the risk of electric shock, do not disassemble this product, but take it to an  
authorized service facility. Opening or removing parts of the telephone base or handset other  
than specified access doors may expose you to dangerous voltages or other risks. Incorrect  
reassembling can cause electric shock when the product is subsequently used.  
12. Do not overload wall outlets and extension cords.  
13. Unplug this product from the wall outlet and refer servicing to an authorized service facility  
under the following conditions:  
A. When the power supply cord or plug is damaged or frayed.  
B. If liquid has been spilled onto the product.  
C. If the product has been exposed to rain or water.  
D. If the product does not operate normally by following the operating instructions. Adjust only  
those controls that are covered by the operation instructions. Improper adjustment of other  
controls may result in damage and often requires extensive work by an authorized technician  
to restore the product to normal operation.  
E. If the product has been dropped and the telephone base and/or handset has been damaged.  
F. If the product exhibits a distinct change in performance.  
14. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk  
of electric shock from lightning.  
15. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain  
circumstances, a spark may be created when the adapter is plugged into the power outlet, or  
when the handset is replaced in its cradle. This is a common event associated with the closing  
of any electrical circuit. The user should not plug the phone into a power outlet, and should  
not put a charged handset into the cradle, if the phone is located in an environment containing  
concentrations of flammable or flame-supporting gases, unless there is adequate ventilation.  
A spark in such an environment could create a fire or explosion. Such environments might  
include: medical use of oxygen without adequate ventilation; industrial gases (cleaning  
solvents; gasoline vapors; etc.); a leak of natural gas; etc.  
16. Only put the handset of your telephone next to your ear when it is in normal talk mode.  
 
9
 
Appendix  
Important.safety.instructions  
17. The power adapter is intended to be correctly oriented in a vertical or floor mount position. The  
prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table  
or cabinet outlet.  
SAVE THESE INSTRUCTIONS  
Battery  
CAUTION: Use Only Supplied Battery.  
Do not dispose of the battery in a fire. Check with local waste management codes for special  
disposal instructions.  
Do not open or mutilate the battery. Released electrolyte is corrosive and may cause burns or  
injury to the eyes or skin. The electrolyte may be toxic if swallowed.  
Exercise care in handling batteries in order not to create a short circuit with conductive materials.  
Charge the battery provided with or identified for use with this product only in accordance with  
the instructions and limitations specified in this manual.  
Precautions for users of implanted cardiac pacemakers  
Cardiac pacemakers (applies only to digital cordless telephones):  
Wireless Technology Research, LLC (WTR), an independent research entity, led a  
multidisciplinary evaluation of the interference between portable wireless telephones and  
implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR  
recommends to physicians that:  
Pacemaker.patients  
Should keep wireless telephones at least six inches from the pacemaker.  
Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket,  
when it is turned ON.  
Should use the wireless telephone at the ear opposite the pacemaker.  
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons  
using wireless telephones.  
About cordless telephones  
Privacy: The same features that make a cordless telephone convenient create some  
limitations. Telephone calls are transmitted between the telephone base and the cordless  
handset by radio waves, so there is a possibility that the cordless telephone conversations  
could be intercepted by radio receiving equipment within range of the cordless handset. For  
this reason, you should not think of cordless telephone conversations as being as private as  
those on corded telephones.  
Electrical.power: The telephone base of this cordless telephone must be connected to a  
working electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls  
cannot be made from the cordless handset if the telephone base is unplugged, switched off or if  
the electrical power is interrupted.  
Potential.TV.interference: Some cordless telephones operate at frequencies that may cause  
interference to televisions and VCRs. To minimize or prevent such interference, do not place  
the telephone base of the cordless telephone near or on top of a TV or VCR. If interference is  
experienced, moving the cordless telephone farther away from the TV or VCR often reduces or  
eliminates the interference.  
Rechargeable.batteries: Exercise care in handling batteries in order not to create a short  
circuit with conducting material such as rings, bracelets, and keys. The battery or conductor  
may overheat and cause harm. Observe proper polarity between the battery and the battery  
charger.  
 
10  
Appendix  
Operating range  
This cordless telephone operates with the maximum power allowed by the Federal Communications  
Commission (FCC). Even so, this handset and telephone base can communicate over only a certain  
distance - which can vary with the locations of the telephone base and handset, the weather, and the  
layout of your home or office.  
When the handset is out of range, the handset displays Out of range OR no power at base.  
If there is a call while the handset is out of range, it may not ring, or if it does ring, the call may not  
connect well when you press  
answer the call.  
or . Move closer to the telephone base, then press  
or  
to  
If the handset moves out of range during a telephone conversation, there may be interference. To  
improve reception, move closer to the telephone base.  
Maintenance  
Taking care of your telephone  
Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.  
Avoid rough treatment  
Place the handset down gently. Save the original packing materials to protect your telephone if  
you ever need to ship it.  
Avoid water  
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or  
handle it with wet hands. Do not install the telephone base near a sink, bathtub or shower.  
Electrical storms  
Electrical storms can sometimes cause power surges harmful to electronic equipment. For your  
own safety, take caution when using electrical appliances during storms.  
Cleaning your telephone  
Your telephone has a durable plastic casing that should retain its luster for many years. Clean  
it only with a soft cloth slightly dampened with water or a mild soap. Do not use excess water or  
cleaning solvents of any kind.  
Remember that electrical appliances can cause serious injury if used when you are wet or  
standing in the water. If the telephone base should fall into the water, DO NOT RETRIEVE IT  
UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL.  
Then remove the telephone by the unplugged cords.  
 
11  
 
Appendix  
The RBRC® seal  
The RBRC® seal on the nickel-metal hydride battery indicates that VTech Communications, Inc. is  
voluntarily participating in an industry program to collect and recycle these batteries at the end of  
their useful lives, when taken out of service within the United States and Canada.  
The RBRC® program provides a convenient alternative to placing used nickel-metal hydride  
batteries into the trash or municipal waste, which may be illegal in your area.  
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers  
participating in the RBRC® program or at authorized VTech product service centers. Please call  
1 (800) 8 BATTERY® for information on Ni-MH battery recycling and disposal bans/restrictions  
in your area. VTech’s involvement in this program is part of its commitment to protecting our  
environment and conserving natural resources.  
RBRC® and 1 (800) 8 BATTERY® are registered trademarks of Rechargeable Battery Recycling  
Corporation.  
 
12  
 
Appendix  
FCC, ACTA and IC regulations  
FCC Part 15  
This equipment has been tested and found to comply with the requirements for a Class B digital  
device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements  
are intended to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television reception, which  
can be determined by turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Changes or modifications to this equipment not expressly approved by the party responsible for  
compliance could void the user’s authority to operate the equipment.  
This device complies with Part 15 of the FCC rules. Operation is subject to the following two  
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause undesired operation. Privacy of  
communications may not be ensured when using this telephone.  
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy  
that can be safely absorbed by a user or bystander according to the intended usage of the product.  
This product has been tested and found to comply with the FCC criteria. The handset may be safely  
held against the ear of the user. The telephone base shall be installed and used such that parts of  
the user’s body other than the hands are maintained at a distance of approximately 20 cm (8 inches)  
or more.  
For body worn operation, this handset has been tested and meets the FCC RF exposure guidelines  
when used with the accessories supplied or designated for this product. Use of other accessories  
may not ensure compliance with FCC RF exposure guidelines.  
This Class B digital apparatus complies with Canadian requirement:  
CAN ICES-3 (B)/NMB-3(B).  
FCC Part 68 and ACTA  
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by  
the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this  
equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX.  
This identifier must be provided to your telephone service provider upon request.  
The plug and jack used to connect this equipment to premises wiring and the telephone network  
must comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant  
telephone cord and modular plug is provided with this product. It is designed to be connected to a  
compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting  
to a single line and an RJ14 jack for two lines. See Installation Instructions in the user’s manual.  
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect  
to your telephone line and still have them ring when you are called. The REN for this product is  
encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03,  
the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more  
information, please contact your telephone service provider.  
This equipment may not be used with Party Lines. If you have specially wired alarm dialing  
equipment connected to your telephone line, ensure the connection of this equipment does not  
disable your alarm equipment. If you have questions about what will disable alarm equipment,  
consult your telephone service provider or a qualified installer.  
 
13  
 
Appendix  
FCC, ACTA and IC regulations  
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has  
been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its  
authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty.  
If this equipment is causing harm to the telephone network, the telephone service provider may  
temporarily discontinue your telephone service. The telephone service provider is required to notify  
you before interrupting service. If advance notice is not practical, you will be notified as soon as  
possible. You will be given the opportunity to correct the problem and the telephone service provider  
is required to inform you of your right to file a complaint with the FCC. Your telephone service  
provider may make changes in its facilities, equipment, operation, or procedures that could affect  
the proper functioning of this product. The telephone service provider is required to notify you if such  
changes are planned.  
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.  
If this product has memory dialing locations, you may choose to store emergency telephone numbers  
(e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:  
Remain on the line and briefly explain the reason for the call before hanging up.  
Perform such activities in off-peak hours, such as early morning or late evening.  
Industry Canada  
This device complies with Industry Canada licence-exempt RSS standard(s).  
Operation is subject to the following two conditions: (1) this device may not cause harmful  
interference, and (2) this device must accept any interference received, including interference that  
may cause undesired operation.  
Privacy of communications may not be ensured when using this telephone.  
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada  
technical specifications were met.  
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an  
indication of the maximum number of devices allowed to be connected to a telephone interface.  
The termination on an interface may consist of any combination of devices subject only to the  
requirement that the sum of the RENs of all the devices does not exceed five.  
This product meets the applicable Industry Canada technical specifications.  
 
14  
Appendix  
California.Energy.Commission.battery.charging.testing.  
instructions  
This telephone is set up to comply with the energy-conserving standards right out of the box.  
These instructions are intended for California Energy Commission (CEC) compliance testing only.  
When then CEC battery charging testing mode is activated, all telephone functions, except battery  
charging, will be disabled.  
To activate the CEC battery charging testing mode:  
1. When the phone is not in use, press MENU, , 2, 3, 2, 7, 3, 8, # and then the left softkey on the  
*
telephone base.  
2. The energy-saving charging mode will be activated in about 60 seconds. You hear a  
confirmation tone from the telephone base.  
When the phone successfully enters the CEC battery charging testing mode, all cordless  
handsets will be deregistered. Then all handsets show Press [HOLD] on base for 4 sec, then  
press [#] on handset.  
When the phone fails to enter this mode, repeat the steps above.  
To.deactivate.the.CEC.battery.charging.testing.mode:  
1. Unplug the telephone base power adapter from the power outlet, then plug it back in. Then the  
telephone base is powered up as normal.  
2. Register the handset back to the telephone base. See page 5 for handset registration instructions.  
 
15  
 
Appendix  
For.C-UL.compliance.only  
Mesures de sécurité importantes  
Afin de réduire les risques d’incendie, de blessures corporelles ou d’électrocution, suivez toujours  
ces mesures préventives de base lorsque vous utilisez votre téléphone :  
1. Lisez et comprenez bien toutes les instructions.  
2. Observez toutes les instructions et mises en garde inscrites sur l’appareil.  
3. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas de nettoyeurs  
liquides ni en aérosol. N’utilisez qu’un chiffon doux et légèrement humecté.  
4. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un évier de cuisine,  
d’un bac de lavage ou d’une piscine, ou dans un sous-sol humide ou sous la douche.  
5. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants. L’appareil pourrait  
tomber et être sérieusement endommagé.  
6. Évitez d’installer le système téléphonique dans les endroits soumis à une température extrême,  
à la lumière directe du soleil ou à proximité immédiate d’autres appareils électriques ou  
électroniques. Protégez votre téléphone contre les sources d’humidité, la poussière, les vapeurs  
et les liquides corrosifs.  
7. Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées à l’arrière ou en  
dessous. Afin d’empêcher la surchauffe, ces ouvertures ne doivent pas être obstruées en plaçant  
l’appareil sur un lit, divan, tapis ou autre surface similaires. Ne placez pas cet appareil à proximité  
d’un élément de chauffage ni d’une plinthe électrique. De plus, ne l’installez pas dans une unité  
murale ou un cabinet fermé qui ne possède pas d’aération adéquate.  
8. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les étiquettes de  
l’appareil. Si vous ne connaissez pas le voltage de votre maison, consultez votre marchand ou  
votre fournisseur d’électricité.  
9. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit sécuritaire, là  
où personne ne pourra trébucher sur la ligne d’alimentation ni le cordon téléphonique modulaire.  
10. N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils pourraient  
toucher à des points de tension dangereux ou court-circuiter des pièces, ce qui constituerait un  
risque d’incendie ou d’électrocution. N’échappez pas de liquides dans l’appareil.  
11. Afin de réduire les risques d’électrocution, ne démontez pas l’appareil, mais apportez-le plutôt à  
un centre de service qualifié s’il doit être réparé. En enlevant le couvercle, vous vous exposez  
à des tensions dangereuses ou autres dangers similaires. Un remontage inadéquat peut être à  
l’origine d’une électrocution lors d’une utilisation ultérieure de l’appareil. Débranchez l’appareil  
avant de procéder au nettoyage. Utilisez un chiffon humide et doux.  
12. Ne surchargez pas les prises de courant et les rallonges.  
13. Débranchez cet appareil de la prise de courant et communiquez avec le département de service  
à la clientèle de VTech dans les cas suivants:  
• Lorsque le cordon d’alimentation est endommagé ou écorché.  
• Si du liquide a été échappé dans l’appareil.  
• Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.  
• Si le produit ne fonctionne pas normalement en respectant les instructions de fonctionnement.  
Réglez uniquement les commandes indiquées dans le les instructions de fonctionnement. Les  
réglages incorrects des autres commandes pourraient provoquer un dommage qui pourrait  
exiger un travail exhaustif de la part d’un technicien autorisé afin de rétablir le fonctionnement  
normal de l’appareil.  
• Si le produit a été échappé et que le socle et/ou le combiné a été endommagé.  
• Si le produit affiche une nette diminution de sa performance.  
 
16  
 
Appendix  
For.C-UL.compliance.only  
14. Évitez d’utiliser un téléphone (autre qu’un sans fil) pendant un orage. Les éclairs peuvent être à  
l’origine d’une électrocution.  
15. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de la fuite. En certaines  
circonstances, une flammèche pourrait être provoquée lorsque l’adaptateur est branché à une  
prise de courant, ou lorsque le combiné est déposé sur le socle. Ceci est un événement commun  
associé à la fermeture d’un circuit électrique. L’utilisateur ne devrait pas brancher le téléphone à  
une prise de courant, et ne devrait pas déposer le combiné chargé sur le socle, si le téléphone  
se trouve à proximité d’un endroit comportant des concentrations de gaz inflammables, à  
moins que la ventilation soit adéquate. Une flammèche dans un tel endroit pourrait provoquer  
un incendie ou une explosion. De tels environnements peuvent comprendre: des endroits où  
l’on utilise de l’oxygène médical sans ventilation adéquate; des gaz industriels (dissolvants de  
nettoyage, des vapeurs d’essence, etc.); une fuite de gaz naturel, etc.  
16. Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en mode de  
conversation.  
17. Ces adaptateurs ont été conçus pour être orientés en position verticale ou montés au sol. Les  
broches ne sont pas conçues pour maintenir l’adaptateur en place si celui-ci est barnché dans une  
prise au plafond ou sous une table/ armoire.  
CONSERVEZ.CES.INSTRUCTIONS  
Pile  
MISE EN GARDE : N’utilisez que la pile incluse.  
Ne jetez pas la pile au feu. Vérifiez les instructions spécifiques de mise aux rebus auprès des  
autorités locales.  
N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est corrosif et pourrait  
causer des brûlures ou des blessures aux yeux ou à la peau. L’électrolyte est toxique si avalé.  
Soyez prudents lorsque vous manipulez les piles afin d’éviter les courts-circuits provoqués par  
des matériaux conducteurs. .  
Rechargez la pile incluse ou identifiée pour fonctionner avec cet appareil, selon les instructions  
et limites spécifiées dans ce guide d’utilisation.  
Stimulateurs cardiaques implantés dans l’organisme  
Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans fil) :  
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante,  
a mené une évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs  
et les stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des  
aliments et drogues (FDA) des États-Unis, la firme WTR recommande aux médecins :  
Avis aux détenteurs de stimulateurs cardiaques  
Ils doivent tenir le téléphone sans fil à une distance d’au moins six pouces du stimulateur  
cardiaque.  
Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que  
dans une poche de chemise, lorsque celui-ci est en marche.  
Ils doivent utiliser le téléphone sans fil en l’appuyant sur l’oreille qui se trouve dans la direction  
opposée au stimulateur cardiaque.  
L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de  
simulateurs cardiaques causés par les gens qui utilisent un téléphone sans fil à proximité de  
ceux-ci.  
 
17  
Appendix  
For.C-UL.compliance.only  
À propos des téléphones sans fil  
Confidentialité : Les mêmes caractéristiques qui constituent des avantages pour les  
téléphones sans fil affichent également des restrictions. Les appels téléphoniques sont  
transmis entre le combiné sans fil et le socle par le biais d’ondes radio ; il y a donc la possibilité  
que vos conversations téléphoniques sans fil soient interceptées par des équipements  
de réception radio se trouvant dans la portée du combiné sans fil. Pour cette raison, vous  
ne devez pas percevoir les communications téléphoniques sans fil comme étant aussi  
confidentielles que celles des téléphones à cordons.  
Alimentation électrique : Le socle de ce téléphone sans fil doit être branché à une prise  
électrique fonctionnelle. La prise électrique ne doit pas être contrôlée par un interrupteur mural.  
Les appels ne pourront pas être effectués du combiné sans fil si le socle est débranché ou mis  
hors tension ou si le courant est coupé.  
Possibilité d’interférences aux téléviseurs : Certains téléphones sans fil fonctionnent sur  
des fréquences pouvant causer des interférences aux téléviseurs et aux magnétoscopes. Pour  
réduire ou prévenir de telles interférences, ne placez pas le socle du téléphone sans fil près ou  
sur un téléviseur ou magnétoscope. S’il y a présence de parasites, il est conseillé d’éloigner  
le téléphone sans fil du téléviseur ou du magnétoscope afin de réduire possiblement les  
interférences.  
Piles rechargeables.: Manipulez les piles avec soin afin de ne pas les court-circuiter avec des  
bagues, bracelets ou clés. Les piles ou le conducteur peut surchauffer et causer des blessures.  
Respectez la polarité adéquate entre la pile et le chargeur.  
Les bloc-piles rechargeables à l’hydrure métallique de nickel :.Jetez ces blocs-piles de  
manière écologique et sécuritaire. Ne les incinérez pas et ne les percez pas. Tel que les autres  
piles de ce type, elles pourraient dégager une matière toxique qui peut causer des blessures  
corporelles si elles sont brûlées ou percées.  
 
18  
Appendix  
Limited warranty  
What does this limited warranty cover?  
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase  
(“Consumer” or “you”) that the Product and all accessories provided in the sales package  
(“Product”) are free from defects in material and workmanship, pursuant to the following terms  
and conditions, when installed and used normally and in accordance with the Product operating  
instructions. This limited warranty extends only to the Consumer for Products purchased and used  
in the United States of America and Canada.  
What will VTech do if the Product is not free from defects in materials and workmanship  
during the limited warranty period (“Materially Defective Product”)?  
During the limited warranty period, VTech’s authorized service representative will repair or replace  
at VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may  
use new or refurbished replacement parts. If we choose to replace the Product, we may replace  
it with a new or refurbished Product of the same or similar design. We will retain defective parts,  
modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive  
remedy. VTech will return the repaired or replacement Products to you in working condition. You  
should expect the repair or replacement to take approximately 30 days.  
How long is the limited warranty period?  
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase.  
If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty,  
this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90  
days from the date the repaired or replacement Product is shipped to you or (b) the time remaining  
on the original one-year warranty; whichever is longer.  
What is not covered by this limited warranty?  
This limited warranty does not cover:  
1. Product that has been subjected to misuse, accident, shipping or other physical damage,  
improper installation, abnormal operation or handling, neglect, inundation, fire, water or other  
liquid intrusion; or  
2. Product that has been damaged due to repair, alteration or modification by anyone other than  
an authorized service representative of VTech; or  
3. Product to the extent that the problem experienced is caused by signal conditions, network  
reliability, or cable or antenna systems; or  
4. Product to the extent that the problem is caused by use with non-VTech accessories; or  
5. Product whose warranty/quality stickers, product serial number plates or electronic serial  
numbers have been removed, altered or rendered illegible; or  
6. Product purchased, used, serviced, or shipped for repair from outside the United States of  
America or Canada, or used for commercial or institutional purposes (including but not limited  
to Products used for rental purposes); or  
7. Product returned without a valid proof of purchase (see item 2 below); or  
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of  
systems outside the unit.  
 
19  
 
Appendix  
Limited warranty  
How do you get warranty service?  
To obtain warranty service in the United States of America, please call 1 (800) 595-9511. In  
Canada, please call 1(800) 267-7377. NOTE: Before calling for service, please review the user’s  
manual - a check of the Product’s controls and features may save you a service call.  
Except as provided by applicable law, you assume the risk of loss or damage during transit and  
transportation and are responsible for delivery or handling charges incurred in the transport of  
the Product(s) to the service location. VTech will return repaired or replaced Product under this  
limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no  
risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited  
warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify  
you and will request that you authorize the cost of repair prior to any further repair activity. You  
must pay for the cost of repair and return shipping costs for the repair of Products that are not  
covered by this limited warranty.  
What must you return with the Product to get warranty service?  
1. Return the entire original package and contents including the Product to the VTech service  
location along with a description of the malfunction or difficulty; and  
2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product  
model) and the date of purchase or receipt; and  
3. Provide your name, complete and correct mailing address, and telephone number.  
Other Limitations  
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all  
other written or oral communications related to this Product. VTech provides no other warranties  
for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the  
Product. There are no other express warranties. No one is authorized to make modifications to  
this limited warranty and you should not rely on any such modification.  
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have  
other rights, which vary from state to state or province to province.  
Limitations: Implied warranties, including those of fitness for a particular purpose and  
merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one  
year from the date of purchase. Some states/provinces do not allow limitations on how long an  
implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be  
liable for any indirect, special, incidental, consequential, or similar damages (including, but not  
limited to lost profits or revenue, inability to use the Product or other associated equipment, the  
cost of substitute equipment, and claims by third parties) resulting from the use of this Product.  
Some states/provinces do not allow the exclusion or limitation of incidental or consequential  
damages, so the above limitation or exclusion may not apply to you.  
Please retain your original sales receipt as proof of purchase.  
 
20  
Appendix  
Technical specifications  
Frequency  
control  
Crystal controlled PLL synthesizer  
Transmit  
Handset: 1921.536-1928.448 MHz  
frequency  
Telephone base: 1921.536-1928.448 MHz  
Channels  
5
Nominal  
Maximum power allowed by FCC and IC. Actual operating range  
effective range may vary according to environmental conditions at the time of use.  
Power  
requirements  
Handset: 2.4V 500mAh Ni-MH battery  
Charger: 6V DC @ 400mA  
Memory  
Handset directory: 50 memory locations;  
up to 30 digits and 15 characters  
Handset call log: 50 memory locations;  
up to 24 digits and 15 characters  
 
21  
 
Designed to fit your home.  
And your life.  
VTech Communications, Inc.  
A member of THE VTECH GROUP OF COMPANIES.  
VTech is a registered trademark of VTech Holdings Limited.  
Specifications are subject to change without notice.  
© 2014 VTech Communications, Inc.  
All right reserved. 12/14. DS6101-X_CIB_V3.0  
Document order number: 91-007066-040-100  
 

Thales Navigation GPS Receiver CGRS User Manual
Toshiba Flat Panel Television 15VL64 User Manual
TP Link Network Router EAP110 User Manual
Tripp Lite Surge Protector IBAR4 User Manual
Tripp Lite TV Cables EZA VGAAF 2 User Manual
Tripp Lite Universal Remote URM 17A User Manual
Victory Refrigeration Refrigerator UR 48 SBS User Manual
Viking Gas Grill VGBQ300 User Manual
Vinotemp Refrigerator VT WINEDISP4 User Manual
Vivitek Home Theater System H118x User Manual