VTech Cordless Telephone DS6301 User Manual

User’s manual  
Accessory handset for use with  
VTech models DS6311/DS6321/  
DS6322  
w w w.v techphones.com  
Model: DS6301  
 
Getting started  
Parts checklist  
Your telephone contains the following items. Save your sales receipt and  
original packaging in the event warranty service is necessary.  
Battery  
Battery  
compartment  
cover  
Handset  
User’s manual  
Charger and power adapter  
To purchase a replacement battery or a power adapter, visit our website at  
 
1
 
Getting started  
Battery installation  
Install the battery as shown below.  
1. If the battery compartment cover is on the handset, press the indentation  
and slide the cover to remove.  
2. Plug the battery connector securely into the socket inside the handset  
battery compartment, matching the color-coded label.  
3. Place the battery with the label THIS SIDE UP facing up and the wires  
inside the battery compartment.  
4. Align the cover flat against the battery compartment, then slide it towards  
the center of the handset until it clicks into place.  
5. Charge the handset by placing it in the telephone base or charger. The  
CHARGE light is on when the handset charges.  
2
3
1
4
5
CHARGE light  
If the handset will not be used for a long time, disconnect and remove  
the battery to prevent possible leakage.  
• To purchase a replacement battery, visit our website at  
 
2
 
Getting started  
Battery charging  
Once you have installed the battery, the screen indicates the battery status  
(see the table below). If necessary, place the handset in the telephone base  
or charger to charge the battery. For best performance, keep the handset in  
the telephone base or charger when not in use. The battery is fully charged  
after 16 hours of continuous charging. See the table on page 8 for battery  
operating times.  
If the screen is blank, you need to charge the handset without interruption for  
at least 10 minutes to give the handset enough charge to use the telephone  
for a short time. When the battery is low, the handset beeps and shows  
Low battery and a flashing . If you are on a call in low battery mode, the  
handset beeps every minute.  
The following table summarizes the battery charge indicators and actions  
to take.  
Battery indicators  
Battery status  
Action  
The screen is blank.  
Battery has no charge  
and the handset cannot  
be used.  
Charge without interruption  
until the screen shows  
HANDSET X (at least  
10 minutes).  
The screen shows  
Place in charger and  
flashes.  
Battery has very little  
charge and the handset  
cannot be used.  
Charge without interruption  
until the screen shows  
HANDSET X (at least  
four minutes).  
The screen shows  
Low battery,  
flashes, and the  
handset beeps.  
Battery has enough  
charge to be used for a  
short time.  
Charge without interruption  
until the screen shows  
HANDSET X (at least  
30 minutes).  
The screen shows  
HANDSET X.  
Battery is charged.  
To keep the battery charged,  
place it in the telephone base  
or charger when not in use.  
 
3
 
Getting started  
Add and register a handset  
You can add new handsets (DS6301, purchased separately) to your  
telephone system, but each handset must be registered with the telephone  
base before use. When first purchased, each expansion handset shows  
Press and hold FIND HANDSET on base for 4 sec, then press # on  
handset after a battery is installed. You may need to charge the handset  
before registering to the telephone base. For more details on battery  
charging, see the table on page 3.  
To register a handset:  
1. Press and hold /FIND HANDSET on the telephone base for about four  
seconds until the red IN USE light turns on.  
2. Press # on the handset. Its screen shows Registering...Please wait and  
it takes up to 60 seconds to complete the registration. The handset shows  
HANDSET X Registered (X represents the handset number assigned)  
and you hear a beep when the registration is completed.  
• If the registration fails, the handset shows Registration failed for a few  
seconds and then Press and hold FIND HANDSET on base for 4 sec,  
then press # on handset. Try the registration process again.  
• You cannot register a handset if any other system handset is in use.  
 
4
 
Getting started  
Replace a handset  
If you want to replace a handset or re-assign the designated handset number  
of a registered handset, you must deregister all the handsets and then  
individually register each handset.  
To make deregistration easier, read all of the instructions on this page before  
you begin.  
To deregister all handsets:  
1. Press and hold /FIND HANDSET on the telephone base for about 10  
seconds until the IN USE light flashes, then release FIND HANDSET.  
2. Press /FIND HANDSET again. You must press /FIND HANDSET  
while the IN USE light is still flashing. The IN USE light flashes for about  
seven seconds.  
3. All system handsets show Out of range OR No power at base for a few  
seconds and then Press and hold FIND HANDSET on base for 4 sec,  
then press # on handset when the deregistration is completed. The  
deregistration process takes about 10 seconds to complete.  
If deregistration fails, you may need to reset the telephone and try again.  
To reset:  
Press and hold OFF/CLEAR or place the handset back in the  
telephone base.  
-OR-  
Unplug the power from the telephone base, then plug it back in.  
After deregistering, register each handset individually. See Add and register  
a handset on page 4.  
You cannot deregister handsets if any system handset is in use.  
 
5
 
Getting started  
Handset layout  
CHARGE light  
On when the handset is charging in the telephone base  
or charger.  
MENU/SELECT  
Press to show the menu.  
While in a menu, press to select an item, or save an entry  
or setting.  
/HOME/FLASH  
Press to make or answer a home call.  
During a home call, press to answer an incoming call  
when you hear a call waiting alert.  
Flashes quickly when there is an incoming home call.  
Flashes slowly when a home call is on hold.  
1
While reviewing a call log entry, press repeatedly  
to add or remove 1 in front of the telephone number  
before dialing or saving it in the directory.  
TONE  
Press to switch to tone dialing temporarily during a call  
if you have pulse service.  
Press to make or answer a home call using the  
handset speakerphone.  
During a call, press to switch between speakerphone  
and handset.  
REDIAL/PAUSE  
Press to review the redial list.  
While dialing or entering numbers into the directory,  
press and hold to insert a dialing pause.  
HOLD  
Press to put a call on hold.  
 
6
 
Getting started  
Handset layout (continued)  
/VOL/  
While in a menu, press to scroll up.  
During a call, press to increase the listening volume.  
When the handset is not in use, press to enter the  
directory.  
OFF/CLEAR  
During a call, press to hang up.  
While the handset is ringing, press to silence the ringer  
temporarily.  
Press and hold while the telephone is not in use to  
erase the displayed messages (XX Missed calls and  
Download dir aborted).  
While in a menu, press to exit without making changes  
or press and hold to return to idle mode.  
While entering or editing a directory entry, press to  
erase a digit or character.  
/CELL  
Press to make or answer a cell call.  
During a cell call, press to answer an incoming call  
when you hear a call waiting alert.  
Flashes quickly when there is an incoming cell call.  
Flashes slowly when a cell call is on hold.  
VOL/CID/  
While in a menu, press to scroll down.  
During a call, press to decrease the listening volume.  
When the handset is not in use, press to review the  
call log.  
#
While reviewing a call log entry or a directory entry,  
press repeatedly to show other dialing options.  
MUTE/REMOVE  
While on a call, press to mute the microphone.  
While reviewing the call log, directory or redial list, press to  
delete an individual entry.  
Press to delete digits when predialing.  
 
7
Appendix  
Battery  
It takes up to 16 hours for the battery to be fully charged. When it is fully charged, you  
can expect the following performance:  
Operation  
Operating time  
While in handset use (talking*)  
Up to 10 hours  
While in speakerphone mode (talking*) Up to seven hours  
While not in use (standby**) Up to 10 days  
*Operating times vary depending on your actual use and the age of the battery.  
**Handset is not charging or in use.  
The battery needs charging when:  
A new battery is installed in the handset.  
The handset beeps every minute while on a call.  
The handset beeps and Low battery displays on the handset.  
Place in charger displays on the handset.  
A battery is properly installed but the screen is blank.  
CAUTION:  
To reduce the risk of fire or injury, read and follow these instructions:  
Use only the battery(ies) provided or equivalent. To order a replacement, visit our  
Do not dispose of the battery(ies) in a fire. Check with local waste management  
codes for special disposal instructions.  
Do not open or mutilate the battery(ies). Released electrolyte is corrosive and  
might cause burns or injury to the eyes or skin. The electrolyte might be toxic  
if swallowed.  
Exercise care in handling batteries in order not to create a short circuit with  
conductive materials.  
Charge the battery(ies) provided with or identified for use with this product only in  
accordance with the instructions and limitations specified in this manual.  
Observe proper polarity orientation between the battery and metallic contacts.  
To prevent fire or shock hazard, do not expose this product to water or any type  
of moisture.  
 
8
 
Appendix  
Important safety instructions  
When using your telephone equipment, basic safety precautions should always be followed to  
reduce the risk of fire, electric shock and injury, including the following:  
1. Read and understand all instructions.  
2. Follow all warnings and instructions marked on the product.  
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners.  
Use a dry non-abrasive cloth for cleaning.  
4. Do not use this product near water.  
5. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.  
6. Slots and openings in the back or bottom of the telephone base and handset are provided for  
ventilation. To protect them from overheating, these openings must not be blocked by placing  
the product on a soft surface such as a bed, sofa or rug. This product should never be placed  
near or over a radiator or heat register. This product should not be placed in any area where  
proper ventilation is not provided.  
7. This product should be operated only from the type of power source indicated on the marking  
label. If you are not sure of the type of power supply in your home, consult your dealer or local  
power company.  
8. Do not allow anything to rest on the power cord. Do not install this product where the cord  
may be walked on.  
9. Never push objects of any kind into this product through the slots in the telephone base or  
handset because they may touch dangerous voltage points or create a short circuit. Never  
spill liquid of any kind on the product.  
10. To reduce the risk of electric shock, do not disassemble this product, but take it to an  
authorized service facility. Opening or removing parts of the telephone base or handset other  
than specified access doors may expose you to dangerous voltages or other risks. Incorrect  
reassembling can cause electric shock when the product is subsequently used.  
11. Do not overload wall outlets and extension cords.  
12. Unplug this product from the wall outlet and refer servicing to an authorized service facility  
under the following conditions:  
A. When the power supply cord or plug is damaged or frayed.  
B. If liquid has been spilled onto the product.  
C. If the product has been exposed to rain or water.  
D. If the product does not operate normally by following the operating instructions. Adjust only  
those controls that are covered by the operation instructions. Improper adjustment of other  
controls may result in damage and often requires extensive work by an authorized technician  
to restore the product to normal operation.  
E. If the product has been dropped and the telephone base and/or handset has been damaged.  
F. If the product exhibits a distinct change in performance.  
13. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote  
risk of electric shock from lightning.  
14. Do not use the telephone to report a gas leak in the vicinity of the leak.  
15. Only put the handset of your telephone next to your ear when it is in normal talk mode.  
16. The power adapter is intended to be correctly oriented in a vertical or floor mount position.  
The prongs are not designed to hold the plug in place if it is plugged into a ceiling or an under-  
the-table/cabinet outlet.  
SAVE THESE INSTRUCTIONS  
 
9
 
Appendix  
Precautions for users of implanted cardiac pacemakers  
Cardiac pacemakers (applies only to digital cordless telephones):  
Wireless Technology Research, LLC (WTR), an independent research entity, led a  
multidisciplinary evaluation of the interference between portable wireless telephones and  
implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR  
recommends to physicians that:  
Pacemaker patients:  
Should keep wireless telephones at least six inches from the pacemaker.  
Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket,  
when it is turned ON.  
Should use the wireless telephone at the ear opposite the pacemaker.  
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons  
using wireless telephones.  
Operating range  
This cordless telephone operates with the maximum power allowed by the Federal  
Communications Commission (FCC). Even so, this handset and telephone base can communicate  
over only a certain distance - which can vary with the locations of the telephone base and  
handset, the weather, and the layout of your home or office.  
When the handset is out of range, the handset displays Out of range OR No power at base.  
If there is a call while the handset is out of range, it might not ring, or if it does ring, the call might  
not connect well when you press  
/HOME/FLASH. Move closer to the telephone base, then  
press /HOME/FLASH to answer the call.  
If the handset moves out of range during a telephone conversation, there might be interference.  
To improve reception, move closer to the telephone base.  
Maintenance  
Taking care of your telephone  
Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.  
Avoid rough treatment  
Place the handset down gently. Save the original packing materials to protect your telephone if  
you ever need to ship it.  
Avoid water  
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or  
handle it with wet hands. Do not install the telephone base near a sink, bathtub or shower.  
Electrical storms  
Electrical storms can sometimes cause power surges harmful to electronic equipment. For your  
own safety, take caution when using electrical appliances during storms.  
Cleaning your telephone  
Your telephone has a durable plastic casing that should retain its luster for many years. Clean  
it only with a soft cloth slightly dampened with water or mild soap. Do not use excess water or  
cleaning solvents of any kind.  
Remember that electrical appliances can cause serious injury if used when you are wet or  
standing in the water. If the telephone base should fall into the water, DO NOT RETRIEVE IT  
UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORD FROM THE WALL.  
Then remove the telephone by the unplugged cords.  
 
10  
 
Appendix  
About cordless telephones  
Privacy: The same features that make a cordless telephone convenient create some  
limitations. Telephone calls are transmitted between the telephone base and the cordless  
handset by radio waves, so there is a possibility that the cordless telephone conversations  
could be intercepted by radio receiving equipment within range of the cordless handset. For  
this reason, you should not think of cordless telephone conversations as being as private as  
those on corded telephones.  
Electrical power: The telephone base of this cordless telephone must be connected to a  
working electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls  
cannot be made from the cordless handset if the telephone base is unplugged, switched off,  
or if the electrical power is interrupted.  
Potential TV interference: Some cordless telephones operate at frequencies that may cause  
interference to televisions and VCRs. To minimize or prevent such interference, do not place  
the telephone base of the cordless telephone near or on top of a TV or VCR. If interference is  
experienced, moving the cordless telephone farther away from the TV or VCR often reduces  
or eliminates the interference.  
Rechargeable batteries: Exercise care in handling batteries in order not to create a short  
circuit with conducting material such as rings, bracelets, and keys. The battery or conductor  
may overheat and cause harm. Observe proper polarity between the battery and the battery  
charger.  
Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do  
not burn or puncture the battery. Like other batteries of this type, if burned or punctured, they  
could release caustic material which could cause injury.  
The RBRC® seal  
The RBRC® seal on the nickel-metal hydride battery indicates that VTech Communications, Inc. is  
voluntarily participating in an industry program to collect and recycle these batteries at the end of  
their useful lives, when taken out of service within the United States and Canada.  
The RBRC® program provides a convenient alternative to placing used nickel-metal hydride  
batteries into the trash or municipal waste, which may be illegal in your area.  
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers  
participating in the RBRC® program or at authorized VTech product service centers. Please call  
1-800-8-BATTERYTM for information on Ni-MH battery recycling and disposal bans/restrictions  
in your area. VTech’s involvement in this program is part of its commitment to protecting our  
environment and conserving natural resources.  
RBRC® is a registered trademark of Rechargeable Battery Recycling Corporation.  
 
11  
 
Appendix  
Warranty  
What does this limited warranty cover?  
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase  
(“Consumer” or “you”) that the Product and all accessories provided in the sales package  
(“Product”) are free from defects in material and workmanship, pursuant to the following terms  
and conditions, when installed and used normally and in accordance with the Product operating  
instructions. This limited warranty extends only to the Consumer for Products purchased and used  
in the United States of America and Canada.  
What will VTech do if the Product is not free from defects in materials and workmanship  
during the limited warranty period (“Materially Defective Product”)?  
During the limited warranty period, VTech’s authorized service representative will repair or replace  
at VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may  
use new or refurbished replacement parts. If we choose to replace the Product, we may replace  
it with a new or refurbished Product of the same or similar design. We will retain defective parts,  
modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive  
remedy. VTech will return the repaired or replacement Products to you in working condition. You  
should expect the repair or replacement to take approximately 30 days.  
How long is the limited warranty period?  
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase.  
If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty,  
this limited warranty also applies to repaired or replacement Product for a period of either (a) 90  
days from the date the repaired or replacement Product is shipped to you or (b) the time remaining  
on the original one-year warranty; whichever is longer.  
What is not covered by this limited warranty?  
This limited warranty does not cover:  
1. Product that has been subjected to misuse, accident, shipping or other physical damage,  
improper installation, abnormal operation or handling, neglect, inundation, fire, water or other  
liquid intrusion; or  
2. Product that has been damaged due to repair, alteration or modification by anyone other than  
an authorized service representative of VTech; or  
3. Product to the extent that the problem experienced is caused by signal conditions, network  
reliability, or cable or antenna systems; or  
4. Product to the extent that the problem is caused by use with non-VTech accessories; or  
5. Product whose warranty/quality stickers, product serial number plates or electronic serial  
numbers have been removed, altered or rendered illegible; or  
6. Product purchased, used, serviced, or shipped for repair from outside the United States of  
America or Canada, or used for commercial or institutional purposes (including but not limited  
to Products used for rental purposes); or  
7. Product returned without a valid proof of purchase (see item 2 below); or  
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of  
systems outside the unit.  
 
12  
 
Appendix  
Warranty  
How do you get warranty service?  
To obtain warranty service in the United States of America, please visit our website at  
dial 1 (800) 267-7377. NOTE: Before calling for service, please review the user’s manual - a check  
of the Product’s controls and features may save you a service call.  
Except as provided by applicable law, you assume the risk of loss or damage during transit and  
transportation and are responsible for delivery or handling charges incurred in the transport of  
the Product(s) to the service location. VTech will return repaired or replaced Product under this  
limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no  
risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited  
warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify  
you and will request that you authorize the cost of repair prior to any further repair activity. You  
must pay for the cost of repair and return shipping costs for the repair of Products that are not  
covered by this limited warranty.  
What must you return with the Product to get warranty service?  
1. Return the entire original package and contents including the Product to the VTech service  
location along with a description of the malfunction or difficulty; and  
2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product  
model) and the date of purchase or receipt; and  
3. Provide your name, complete and correct mailing address, and telephone number.  
Other limitations  
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all  
other written or oral communications related to this Product. VTech provides no other warranties  
for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the  
Product. There are no other express warranties. No one is authorized to make modifications to this  
limited warranty and you should not rely on any such modification.  
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have  
other rights, which vary from state to state or province to province.  
Limitations: Implied warranties, including those of fitness for a particular purpose and  
merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one  
year from the date of purchase. Some states/provinces do not allow limitations on how long an  
implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be  
liable for any indirect, special, incidental, consequential, or similar damages (including, but not  
limited to lost profits or revenue, inability to use the Product or other associated equipment, the  
cost of substitute equipment, and claims by third parties) resulting from the use of this Product.  
Some states/provinces do not allow the exclusion or limitation of incidental or consequential  
damages, so the above limitation or exclusion may not apply to you.  
Please retain your original sales receipt as proof of purchase.  
 
13  
Appendix  
FCC, ACTA and IC regulations  
FCC Part 15  
This equipment has been tested and found to comply with the requirements for a Class B digital  
device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements  
are intended to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television reception, which  
can be determined by turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Changes or modifications to this equipment not expressly approved by the party responsible for  
compliance could void the user’s authority to operate the equipment.  
This device complies with Part 15 of the FCC rules. Operation is subject to the following two  
conditions: (1) this device may not cause harmful interference, and (2) this device must accept  
any interference received, including interference that may cause undesired operation. Privacy of  
communications may not be ensured when using this telephone.  
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy  
that can be safely absorbed by a user or bystander according to the intended usage of the product.  
This product has been tested and found to comply with the FCC criteria. The handset may be safely  
held against the ear of the user. The telephone base shall be installed and used such that parts of  
the user’s body other than the hands are maintained at a distance of approximately 20 cm (8 inches)  
or more.  
This Class B digital apparatus complies with Canadian ICES-003.  
FCC Part 68 and ACTA  
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by  
the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this  
equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX.  
This identifier must be provided to your telephone service provider upon request.  
The plug and jack used to connect this equipment to premises wiring and the telephone network  
must comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant  
telephone cord and modular plug is provided with this product. It is designed to be connected to a  
compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting  
to a single line and an RJ14 jack for two lines. See Installation Instructions in the user’s manual.  
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect  
to your telephone line and still have them ring when you are called. The REN for this product is  
encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03,  
the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more  
information, please contact your telephone service provider.  
This equipment may not be used with Party Lines. If you have specially wired alarm dialing  
equipment connected to your telephone line, ensure the connection of this equipment does not  
disable your alarm equipment. If you have questions about what will disable alarm equipment,  
consult your telephone service provider or a qualified installer.  
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has  
been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its  
authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty.  
 
14  
 
Appendix  
FCC, ACTA and IC regulations  
If this equipment is causing harm to the telephone network, the telephone service provider may  
temporarily discontinue your telephone service. The telephone service provider is required to notify  
you before interrupting service. If advance notice is not practical, you will be notified as soon as  
possible. You will be given the opportunity to correct the problem and the telephone service provider  
is required to inform you of your right to file a complaint with the FCC. Your telephone service  
provider may make changes in its facilities, equipment, operation, or procedures that could affect  
the proper functioning of this product. The telephone service provider is required to notify you if such  
changes are planned.  
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.  
If this product has memory dialing locations, you may choose to store emergency telephone  
numbers (e.g., police, fire, medical) in these locations. If you do store or test emergency numbers,  
please:  
Remain on the line and briefly explain the reason for the call before hanging up.  
Perform such activities in off-peak hours, such as early morning or late evening.  
Industry Canada  
Operation is subject to the following two conditions: (1) this device may not cause harmful  
interference, and (2) this device must accept any interference, including interference that may cause  
undesired operation.  
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada  
technical specifications were met.  
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an  
indication of the maximum number of devices allowed to be connected to a telephone interface.  
The termination on an interface may consist of any combination of devices subject only to the  
requirement that the sum of the RENs of all the devices does not exceed five.  
This product meets the applicable Industry Canada technical specifications.  
 
15  
Appendix  
Technical specifications  
Frequency  
control  
Crystal controlled PLL synthesizer  
Transmit  
Handset: 1921.536-1928.448 MHz  
frequency  
Telephone base: 1921.536-1928.448 MHz  
Channels  
5
Nominal  
Maximum power allowed by FCC and IC. Actual operating range  
effective range might vary according to environmental conditions at the time of  
use.  
Size  
Handset: 6.45 X 1.81 X 1.17 in (163.8 X 46 X 29.8 mm)  
Charger: 2.02 X 3.03 X 3.77 in (51.4 X 76.9 X 95.7 mm)  
Weight  
Handset: 4.44oz (126g) (including battery)  
Charger: 2.43oz (69g)  
Power  
requirements  
Handset: 2.4V 500mAh Ni-MH battery  
Charger: 6V AC @ 300mA  
Memory  
Handset directory: 200 memory locations;  
up to 30 digits and 15 characters  
Four download directories: 1,500 memory locations (each);  
up to 30 digits and 15 characters  
Handset call log: 50 memory locations;  
up to 24 digits and 15 characters  
 
16  
 
The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc.  
and any use of such marks by VTech Holdings Limited is under license.  
VTech Holdings Limited is a member of Bluetooth SIG, Inc.  
Other trademarks and trade names are those of their respective owners.  
VTECH TELECOMMUNICATIONS LTD.  
A member of THE VTECH GROUP OF COMPANIES.  
Distributed in the U.S.A. by VTech Communications, Inc. Beaverton, Oregon 97008  
Distributed in Canada by VTech Technologies Canada, Ltd., Richmond, B.C. V6W 1L5  
Copyright © 2009 for VTECH TELECOMMUNICATIONS LTD.  
Printed in China.  
91-002521-010-100  
 

Technicolor Thomson Camcorder 5400LDK User Manual
Technicolor Thomson CD Player LAD870 User Manual
Technicolor Thomson CD Player PDP2030 User Manual
Tekkeon Battery Charger MP3700 User Manual
Tiffen Carrying Case F 8 User Manual
Toshiba Flat Panel Television P42LHA User Manual
True Fitness Treadmill Z5 Series User Manual
Uniden Cordless Telephone DXAI685 User Manual
Vantec Laptop LPC 401 User Manual
ViewSonic Computer Monitor VS13780 User Manual