VTech Cordless Telephone LS6191 LS6191 13 LS6191 15 LS6191 16 LS6191 17 User Manual

Abridged user’s manual  
LS6191/LS6191-13/LS6191-15/  
LS6191-16/LS6191-17  
DECT 6.0 cordless telephone with  
BLUETOOTH® wireless technology  
Register online to get an additional 3-month warranty!  
Go to www.vtechphones.com to register your product for enhanced warranty  
support and latest VTech product news.  
Compatible with  
Hearing Aid T-Coil  
Telephones identified with this logo have reduced noise and  
interference when used with most T-coil equipped hearing aids and  
cochlear implants. The TIA-ꢀ083 Compliant Logo is a trademark of the  
Telecommunications Industry Association. Used under license.  
T
TIA-1083  
The ENERGY STAR® program (www.energystar.gov) recognizes and  
encourages the use of products that save energy and help protect our  
environment. We are proud to mark this product with the ENERGY STAR®  
label indicating it meets the latest energy efficiency guidelines.  
Introduction  
To help protect the environment, this abridged user’s manual provides you with  
basic installation and use instructions. A limited set of features are described in  
abbreviated form.  
Please refer to the online Complete user’s manual for a full set of installation and  
operation instructions at www.vtechphones.com.  
Before using this VTech product, please read Important safety instructions on  
page ꢀ3 of this user’s manual.  
Parts checklist  
Your telephone package contains the following items. Save your sales receipt and  
original packaging in the event warranty service is necessary.  
Handset  
Telephone base  
Telephone line cord  
THIS SIDE UP  
Battery Pack Bloc-piles  
(2.4V Ni-MH)  
WARNING AVERTISSEMENT  
/
CE CÔTÉ VERS LE HAUT  
/
:
/
:
DO NOT BURN OR PUNCTURE BATTERIES.  
NE PAS INCINÉRER OU PERCER LES PILES.  
Made in China / Fabriqué en chine  
Telephone base  
power adapter  
Battery compartment  
cover  
Battery  
Quick start guide  
Abridged user’s manual  
Abridged user’s manual  
Quick start guide  
 
Battery charging  
Once you have installed the battery, the handset screen indicates the battery  
status. For best performance, keep the handset in the telephone base when not in  
use. The battery is fully charged after hours of continuous charging.  
Battery indicators  
Battery status  
Action  
The screen is blank, or  
displays Put in charger  
and flashes.  
The battery has no or very  
little charge. The handset  
cannot be used.  
Charge without interruption  
(at least 30 minutes).  
The screen displays  
Low battery and flashes.  
The battery has enough  
charge to be used for a  
short time.  
Charge without interruption  
(about 30 minutes).  
The screen displays  
HANDSET 1.  
The battery is charged.  
To keep the battery charged,  
place it in the telephone base  
when not in use.  
Handset overview  
CID/ /VOLUME  
• Review the caller ID log when the  
phone is not in use.  
/
/VOLUME  
• Decrease the listening volume  
during a call or message playback.  
• Review the directory when the  
phone is not in use.  
• Scroll down while in a menu, or  
in the directory, caller ID log or  
redial list.  
• Move the cursor to the left when  
entering numbers or names.  
• Increase the listening volume  
during a call or message  
playback.  
• Scroll up while in a menu, or  
in the directory, caller ID log or  
redial list.  
MENU/SELECT  
• Move the cursor to the right when  
entering numbers or names.  
• Show the menu.  
• While in a menu, press to  
select an item, or save an  
entry or setting.  
• Make or answer a cell call.  
• Answer an incoming cell call  
when you hear a call waiting alert.  
OFF/CANCEL  
• Hang up a call.  
• Silence the handset ringer  
temporarily while the phone  
is ringing.  
/FLASH  
• Make or answer a home call.  
Answer an incoming home call  
when you hear a call waiting alert.  
Press and hold to erase the  
missed call indicator while the  
handset is not in use.  
• Press to return to the previous  
menu, or press and hold to  
return to idle mode, without  
making changes.  
• Press repeatedly to add or  
remove ꢀ in front of the caller ID  
log entry before dialing or saving  
it to the directory.  
Dialing keys  
• Press and hold to set or dial  
your voicemail number.  
• Enter numbers or characters.  
• Answer an incoming call.  
• Switch to tone dialing  
temporarily during a call.  
• Press repeatedly to show other  
dialing options when reviewing  
a caller ID log entry.  
• Press and hold to set and turn  
on the quiet mode, or turn it off.  
• Make a home line call using the  
handset speakerphone.  
• Answer a call using the handset  
speakerphone.  
• During a call, press to switch between the  
speakerphone and the handset earpiece.  
MUTE/DELETE  
• Mute the microphone during a call.  
• Delete digits or characters while using  
the dialing keys.  
REDIAL/PAUSE  
• Press repeatedly to review the redial list.  
Silence the handset ringer temporarily  
while the phone is ringing.  
• Delete the displayed entry while in the  
directory, caller ID log or redial list.  
• Press and hold to insert a dialing pause  
while dialing or entering a number.  
Telephone base overview  
/FIND HANDSET  
Press to page the system handset.  
Bottom of the telephone base  
3
 
Telephone base overview  
/MUTE  
CID/FLASH  
• Tap to review the directory when the  
phone is not in use.  
• Tap to review the caller ID log when the  
phone is not in use.  
• Tap to mute the microphone during  
a call.  
• Tap to answer another incoming call  
during a call on the same line.  
• Tap to silence the base ringer  
temporarily while the phone is ringing.  
1
• Press repeatedly to add or  
remove ꢀ in front of the caller  
ID log entry before dialing or  
saving it to the directory.  
• Tap to pair or replace a  
cell phone.  
Dialing keys (0-9,  
&
)
• Press repeatly to show  
other dialing options when  
reviewing a caller ID log  
entry.  
• Press and hold to turn off  
the quiet mode.  
• Press to enter numbers  
or characters.  
• Press to answer an  
incoming call.  
• Press to make, answer or end a  
cell call.  
• Press to switch to tone dialing  
temporarily during a call.  
• Press to make, answer or end a  
home call.  
3x  
• Tap to play or stop playing messages.  
• Press to delete the playing message.  
4
2
• Press to repeat the playing message.  
• Press to skip to the next message.  
• Press twice to play the previous  
message.  
-
+
VOL /  
VOL /  
• Tap to decrease the  
listening volume during a  
call or message playback.  
• Tap to increase the listening  
volume during a call or  
message playback.  
• Tap to increase the  
telephone base ringer  
volume when the base is  
not in use.  
• Tap to decrease the  
telephone base ringer  
volume when the base is  
not in use.  
• Tap to scroll up while in the  
directory or caller ID log.  
Tap to scroll down  
while in the directory or  
caller ID log.  
• Tap to delete digits or  
characters while predialing.  
Bluetooth  
To use a Bluetooth enabled cell phone with your LS6191, you must first pair and  
connect your Bluetooth cell phone(s) with the telephone base. All LS6191 handsets  
can be used to make or answer calls on the cell line.  
Bluetooth wireless technology operates within a short range (a maximum of  
approximately 30 feet). When you pair a Bluetooth cell phone to the telephone  
base, make sure your Bluetooth cell phone is close to the telephone base to  
maintain sufficient signal strength. For optimal performance, keep your cell phone  
within ꢀ5 feet of the telephone base while using the cell line.  
Pair and connect your first Bluetooth cell phone  
ꢀ. Tap  
on the telephone base. You hear two beeps. The telephone base  
displays Pairing D1... and the 1 icon flashes.  
2. Turn on the Bluetooth feature of your cell phone. Once your cell phone finds  
your VTech phone (VTech LS6191), press the appropriate key on your cell  
phone to continue the pairing process.  
• Your cell phone may prompt you to enter the PIN of the telephone base.  
The default PIN of the telephone base is 0000.  
 
Download directory  
ꢀ. Press MENU on the handset when the phone is not in use.  
2. Scroll to Bluetooth then press SELECT.  
3. Scroll to Download dir then press SELECT.  
ꢁ. Scroll to select the desired cell phone, then press SELECT.  
For Android and Blackberry cell phones, you may also download your  
cell phone directory to your LS6191 via the VTech Contact Share  
application download.  
Using the handset menu  
ꢀ. Press MENU when the phone is not in use.  
2. Press or until the screen displays the desired feature menu.  
3. Press SELECT.  
To return to the previous menu, press CANCEL.  
To return to idle mode, press and hold CANCEL.  
Telephone settings  
Default settings are indicated by asterisks (*).  
Settings menu  
LCD language  
Description  
Options  
English*  
Set the handset display language.  
Français  
Español  
Voicemail #  
Clr voicemail  
Key tone  
Set the voicemail number for speed dialing.  
Voicemail #  
_
Turn off the voicemail indicators (see the  
note below).  
Reset VM Icon?  
Set whether the handset beeps whenever a  
key is pressed.  
Key tone:On*  
Key tone:Off  
Home area code  
Dial mode  
Set the home area code so that the caller ID  
log stores only seven digits for local  
telephone numbers.  
Home area code  
_ _ _  
Set the telephone to be touch-tone or  
pulse dialing.  
Touch-tone*  
Pulse  
Use the Clr voicemail feature when the telephone indicates there is new voicemail  
but there is none. For example, when you have accessed your voicemail while away  
from home. The Clr voicemail feature only turns off the indicators; it does not delete  
your voicemail messages. As long as you have new voicemail messages, your  
telephone service provider continues to send the signal that turns on the indicators.  
The following are some of the telephone features you may wish to set. Refer  
to Telephone settings in the online Complete user’s manual for complete  
instructions on setting all telephone features.  
Handset ringer volume  
You can adjust the handset ringer volume level, or turn the ringer off.  
ꢀ. Press MENU when the handset is not in use.  
2. Scroll to Ringers and then press SELECT.  
3. Scroll to choose Home volume or Cell volume, then press SELECT.  
ꢁ. Press or to sample each volume level, then press SELECT to save.  
When the ringer volume is set to Off, the handset still rings when you press  
/FIND HANDSET at the bottom of the telephone base.  
Quiet mode  
You can turn on the quiet mode for a period of time. During this period, all tones  
(except paging tone) are muted. When you turn on the quiet mode, the answering  
system turns on automatically.  
ꢀ. Press and hold  
when the handset is not in use.  
2. Use the dialing keys (0-9) to enter the duration (hour), then press SELECT to save.  
To turn off the quiet mode, press and hold on the handset or  
telephone base when the phone is not in use.  
on the  
5
 
Set date and time  
If you subscribe to caller ID service, the day, month and time are set automatically  
with each incoming call. You can also set the date and time manually.  
ꢀ. Press MENU on the handset when not in use.  
2. Scroll to Set date/time and then press SELECT.  
3. Use the dialing keys (0-9) to enter the month (MM), date (DD) and year (YY).  
Then press SELECT.  
ꢁ. Use the dialing keys (0-9) to enter the hour (HH) and minute (MM).  
Then press or to choose AM or PM.  
5. Press SELECT.  
Telephone operation  
Make a home call on the cordless handset:  
Press  
or , and then dial the telephone number.  
Make a home call at the telephone base:  
Press  
, then dial the telephone number.  
Make a cell call on the cordless handset:  
ꢀ. Press . Scroll to select the desired cell phone when  
necessary, then press SELECT.  
2. Enter the telephone number and then press to dial.  
While using the cell line, place your cell phone closer to the  
telephone base, and make sure that there are no physical  
obstacles between the telephone base and the cell phone,  
such as large furniture or thick walls.  
Make a cell call at the telephone base:  
ꢀ. Press . Scroll to select the desired cell phone when  
necessary, then press  
.
2. Enter the telephone number and then press to dial.  
Answer a home/cell call on the cordless handset:  
Press  
,
,
or any dialing key.  
Answer a home/cell call at the telephone base:  
Press  
,
or any dialing key.  
End a home/cell call on the cordless handset:  
Press OFF or put the handset back in the telephone base.  
End a home/cell call at the telephone base:  
For a home line call, press  
.
For a cell line call, press  
.
Handset speakerphone  
During a call, press  
handset earpiece.  
to switch between the handset speakerphone and the  
Volume  
To adjust the listening volume on the cordless handset:  
During a call, press /VOLUME or /VOLUME.  
To adjust the listening volume on the telephone base:  
+
-
During a call, tap VOL or VOL .  
Mute  
The mute function allows you to hear the other party but the other party cannot hear you.  
ꢀ. During a call, press MUTE on the handset or tap MUTE on the telephone base.  
The screen displays Muted.  
2. Press MUTE on the handset or tap MUTE on the telephone base again to  
resume the conversation. The screen displays Microphone on briefly.  
Call waiting  
When you subscribe to call waiting service from your telephone service provider,  
you hear an alert tone if there is an incoming call while you are already on a call.  
Call waiting on the home line:  
Press FLASH on the cordless handset or tap FLASH on the telephone base to  
put the current call on hold and take the new call.  
Press FLASH on the cordless handset or tap FLASH on the telephone base at  
any time to switch back and forth between calls.  
6
 
Call waiting on the cell line:  
Press on the cordless handset or tap FLASH on the telephone base to put  
the current call on hold and take the new call.  
Press on the cordless handset or tap FLASH on the telephone base at any  
time to switch back and forth between calls.  
Temporary ringer silencing  
When the telephone is ringing, you can temporarily silence the telephone base/  
handset ringer without disconnecting the call. The next call rings normally at the  
preset volume.  
To silence the handset ringer, press OFF or MUTE on the handset.  
and Ringer muted displays briefly.  
displays  
To silence the telephone base ringer, tap MUTE or VOL- on the telephone base.  
displays and Ringer muted displays briefly.  
Temporary tone dialing  
If you have pulse (rotary) service only, you can switch from pulse to touch-tone  
dialing temporarily during a call.  
ꢀ. During a call, press  
on the handset or  
on the telephone base.  
2. Use the dialing keys to enter the relevant number. The telephone sends  
touch-tone signals. It automatically returns to pulse dialing mode after you  
end the call.  
Find handset  
Use this feature to find the system handset.  
To start paging:  
Press /FIND HANDSET at the bottom of the  
telephone base. The idle handset rings and displays  
Paging  
To end paging:  
Press /FIND HANDSET at the bottom of the telephone base.  
-OR-  
.
Press  
,
,
, OFF or any dialing key on the cordless handset.  
-OR-  
Place the cordless handset in the telephone base.  
Do not press and hold /FIND HANDSET for more than four seconds. It may lead to  
handset deregistration.  
Redial list  
Each handset stores the last ꢀ0 telephone numbers dialed. When there are already  
ꢀ0 entries, the oldest entry is deleted to make room for the new entry.  
To review and dial a number from the redial list on the cordless handset:  
ꢀ. Press REDIAL when the handset is not in use.  
2. Press  
3. Press  
,
or REDIAL repeatedly until the desired entry displays.  
or  
,
to dial.  
To delete a redial entry on the cordless handset:  
When the desired redial entry displays, press DELETE.  
Join a call in progress  
You can use the telephone base and the cordless handset, or two cordless  
handsets at a time on a home line call. You can buy additional expansion handsets  
(LS6001/LS6001-13/LS6001-15/LS6001-16/LS6001-17) for this telephone base.  
You can register up to five handsets to the telephone base.  
When a device is on a home line call, press  
or  
on another cordless  
handset, or press on the telephone base to join the call.  
To exit the call, press OFF on the cordless handset or place it on the telephone  
base, or press  
hang up.  
on the telephone base. The call continues until all devices  
Transfer a call  
While on an outside call, you can transfer the call from one handset to another  
system device. You can only use the handset to transfer a call.  
ꢀ. During a call, press MENU.  
2. Press or to scroll to Transfer, then press SELECT. When you have more  
than one handset, use the dialing keys to enter a destination device number  
(7 for the telephone base, or 1 to 5 for HANDSET 1 to HANDSET 5).  
3. To answer the call on the telephone base, press  
-OR-  
,
or any dialing key.  
To answer the call on the cordless handset, press  
,
,
or any dialing key.  
7
 
Intercom  
Use the intercom feature for conversations between the telephone base and the  
cordless handset, or two cordless handsets. You can only use the handset to  
initiate an intercom call.  
ꢀ. Press MENU on the handset when not in use.  
2. Press or to scroll to Intercom, then press SELECT. When you have more  
than one handset, use the dialing keys to enter a destination device number  
(7 for the telephone base, or 1 to 5 for HANDSET 1 to HANDSET 5).  
3. To answer the intercom call with the destination handset, press  
dialing key.  
,
,
or any  
-OR-  
To answer the intercom call with the telephone base, press  
dialing key.  
,
or any  
ꢁ. To end the intercom call with the cordless handset, press OFF or return the  
cordless handset to the telephone base.  
-OR-  
To end the intercom call with the telephone base, press  
.
Answer an incoming call during an intercom call  
If you receive an outside call during an intercom call, there is an alert tone.  
Using the cordless handset:  
To answer a home call, press  
To answer a cell call, press OFF to end the intercom call. The telephone  
continues to ring. Then press  
. The intercom call ends automatically.  
.
To end the intercom call without answering the outside call, press OFF.  
The intercom call ends and the telephone continues to ring.  
Using the telephone base:  
To answer a home call, press  
to end the intercom call. The telephone  
continues to ring. Then press  
.
To answer a cell call, press  
to end the intercom call. The telephone continues  
to ring. Then press  
.
To end the intercom call without answering the outside call, press  
The intercom call ends and the telephone continues to ring.  
.
Directory  
The directory can store up to 200 directory entries which are shared by the  
telephone base and all system handsets. You can only use the handset to add,  
edit or delete directory entries.  
To add a directory entry:  
ꢀ. Enter the number (up to 30 digits) when the phone is not in use, then press  
SELECT. Then go to Step 3.  
-OR-  
When the phone is not in use, press MENU then scroll to Directory, and then  
press SELECT twice.  
2. Use the dialing keys to enter the number (up to 30 digits).  
-OR-  
Copy a number from the redial list by pressing REDIAL and then press  
,
or  
REDIAL repeatedly to select a number. Press SELECT to copy the number.  
3. Press SELECT to move on to enter the name.  
ꢁ. Use the dialing keys to enter the name (up to ꢀ5 characters). Additional key  
presses show other characters of that particular key.  
5. Press SELECT to save.  
While entering names and numbers, you can:  
Press DELETE to backspace and erase a digit or character.  
Press and hold DELETE to erase the entire entry.  
Press or to move the cursor to the left or right.  
Press and hold PAUSE to insert a dialing pause (for entering numbers only).  
Press 0 to add a space (for entering names only).  
To review and dial a number from the directory:  
Entries are sorted alphabetically.  
ꢀ. Press  
in use.  
on the handset or tap  
on the telephone base when the phone is not  
2. Scroll to browse through the directory, or use the dialing keys to start a name search.  
3. When the desired entry appears, press  
-OR-  
,
or  
on the handset to dial.  
When the desired entry appears, press  
or on the telephone base to dial.  
8
 
To edit a directory entry:  
ꢀ. When the desired entry displays, press SELECT.  
2. Use the dialing keys to edit the number, then press SELECT.  
3. Use the dialing keys to edit the name, then press SELECT.  
To delete a directory entry:  
ꢀ. When the desired entry displays, press DELETE.  
2. When the handset displays Delete contact?, press SELECT.  
To delete all directory entries:  
ꢀ. Press MENU when the phone is not in use.  
2. Scroll to Directory and then press SELECT.  
3. Scroll to Del all conts then press SELECT twice.  
Speed dial  
You can copy up to nine directory entries into the speed dial locations (0 and 2-9)  
so that you can dial these numbers via the home line more quickly. You can only  
use the handset to assign or delete speed dial entries.  
To assign a speed dial entry:  
ꢀ. Press MENU when the phone is not in use.  
2. Scroll to Directory, then press SELECT.  
3. Scroll to Speed dial, then press SELECT.  
ꢁ. Scroll to a desired speed dial location, then press SELECT.  
5. Scroll to a desired directory entry, then press SELECT.  
To dial a speed dial entry:  
Press and hold a dialing key (0 or 2-9) to dial the number stored in the  
corresponding location.  
To delete a speed dial entry:  
ꢀ. Press MENU when the phone is not in use.  
2. Scroll to Directory, then press SELECT.  
3. Scroll to Speed dial, then press SELECT.  
ꢁ. Scroll to a desired speed dial location, then press DELETE. The screen  
displays Clear SD #X? Press SELECT.  
Caller ID  
This product supports caller ID services provided by most telephone service  
providers. Depending on your service subscription, you may see the caller’s name,  
number, date and time of calls that are sent by your telephone service provider  
after the first or second ring.  
Caller ID log  
The caller ID log stores up to 50 entries. If you answer a call before the caller ID  
information displays, it will not be saved in the caller ID log.  
The handset and telephone base display XX missed calls when you have  
incoming calls that have not been answered.  
If you want to erase the missed call indicator, press and hold CANCEL on the  
idle handset.  
To review and dial a number in the caller ID log:  
ꢀ. Press CID on the handset or tap CID on the telephone base when the phone is  
not in use.  
2. Scroll to browse through the caller ID log. When the desired entry appears:  
• Press  
on the handset or  
on the telephone base repeatedly to show  
different dialing options.  
• Press 1 repeatedly if you need to add or remove ꢀ in front of the  
telephone number.  
3. To dial the displayed number with the cordless handset, press  
-OR-  
,
or  
.
To dial the displayed number with the telephone base, press  
or  
.
To save a caller ID log entry to the directory with the handset:  
ꢀ. When the desired caller ID log entry displays, press SELECT.  
2. Use the dialing keys to modify the number, if necessary. Then press SELECT.  
3. Use the dialing keys to modify the name, if necessary. Then press SELECT.  
To delete a caller ID log entry with the handset:  
When the desired caller ID log entry displays, press DELETE.  
To delete all caller ID log entries with the handset:  
ꢀ. Press MENU when the phone is not in use.  
2. Scroll to Caller ID log and then press SELECT.  
3. Scroll to Del all calls then press SELECT twice.  
9
 
About answering system and voicemail  
Your telephone has separate indicators for two different types of voice messages:  
those left on the built-in answering system and those left at your telephone service  
provider’s voicemail. Each alerts you to new messages differently.  
If  
on the telephone base flashes, and XX new messages displays on the  
cordless handset and the telephone base, there are new messages in the built-  
in answering system. It can record up to 59 messages, depending on the length  
of each message. Each message can be up to three minutes in length. The total  
recording time is approximately ꢀꢁ minutes.  
If  
and New voicemail display on the screens, your telephone service  
provider is indicating that it has new voicemail for you. Contact your telephone  
service provider for more information on how to access your voicemail.  
Answering system settings  
Default settings are indicated by asterisks (*).  
Settings menu  
Call screening  
Description  
Options  
Set whether you hear the callers on the base  
while they are leaving messages to you.  
Screening: On*  
Screening: Off  
# of rings  
Set the number of times the telephone rings  
before the answering system answers.  
6; 5; 4; 3*; 2;  
Toll saver  
Remote code  
Set a two-digit security code to access the  
answering system remotely from any touch-  
tone telephone.  
19*  
Msg alert tone  
Recording time  
Set whether the telephone beeps every  
ꢀ0 seconds to alert you of new messages.  
Tone: Off*  
Tone: On  
Set the recording time for each incoming  
message.  
3 minutes*  
2 minutes  
1 minute  
Set number of rings  
You can set the answering system to answer an incoming call after two, three,  
four, five or six rings; or toll saver. If you choose toll saver, the answering system  
answers a call after two rings when you have new messages, or after four rings  
when you have no new messages.  
ꢀ. Press MENU on the handset when the phone is not in use.  
2. Scroll to Answering sys and then press SELECT.  
3. Scroll to Ans sys setup and then press SELECT.  
ꢁ. Scroll to # of rings and then press SELECT.  
5. Press or to choose 6, 5, 4, 3, 2 or Toll saver and then press SELECT.  
Record your own announcement  
You can use the preset announcement to answer calls, or replace it with your own  
recorded announcement. The announcement can be up to 90 seconds in length.  
ꢀ. Press MENU on the handset when the phone is not in use.  
2. Scroll to Answering Sys then press SELECT twice.  
3. The handset announces, To play, press 2. To record, press 7.”  
Then press 7 to record.  
ꢁ. The handset announces, “Record after the tone. Press 5 when you are done.”  
After the tone, speak towards the handset microphone.  
5. Press 5 when done.  
Answering system operation  
Turn the answering system on or off  
The answering system must be turned on to answer and record messages.  
ꢀ. Press MENU when the handset is not in use.  
2. Scroll to Answering sys and then press SELECT.  
3. Scroll to Answer on/off and then press SELECT.  
ꢁ. Press or to choose Answer: On or Answer: Off and then press SELECT.  
ꢀ0  
 
Message playback at the telephone base  
Tap  
when the phone is not in use.  
Options during playback:  
+
-
Tap VOL or VOL to adjust the speaker volume.  
Press 2 to skip to the next message.  
Press 4 to repeat the playing message. Press 4 twice to listen to the  
previous message.  
Press 3x to delete the playing message. The system advances to the  
next message.  
Tap  
to stop.  
Call intercept  
If you want to talk to the person whose message is being recorded, press  
,
or  
on the cordless handset, or  
or on the telephone base.  
Add and register a handset  
The cordless handset provided with your phone system is already registered. Each  
handset is assigned a number that displays on the handset. Additional handsets  
registered to the telephone system are assigned numbers in the sequential order.  
This telephone system accomodates up to five handsets.  
You can add new handsets (LS6001/LS6001-13/LS6001-15/LS6001-16/LS6001-17  
,
purchased seperately) to your telephone system. Each handset must be registered  
with the telephone base before use. When first purchased and properly charged,  
each expansion handset alternately displays To register HS... and ...see manual.  
The new handset should be charged without interruption for at least 30 minutes  
before registering it to the telephone base.  
To register a handset:  
ꢀ. At the bottom of the telephone base, press and hold  
/FIND HANDSET for about four seconds until it shows  
Registering...  
2. On the cordless handset, press  
then it shows  
Registering... Both the telephone base and cordless  
handset show Registered and you hear a beep when  
the registration process completes. The registration  
process takes about 60 seconds to complete.  
Replace a handset  
If you want to replace a handset or reassign the designated handset number of  
a registered handset, you must deregister all handsets and then deregister each  
handset individually.  
To deregister all handsets:  
ꢀ. Press and hold /FIND HANDSET at the bottom of the telephone base for about  
ꢀ0 seconds until the telephone base shows Registering... then De-register?  
2. Immediately press /FIND HANDSET again. You hear a confirmation tone.  
3. All handsets alternately show To register HS... and ...see manual. The  
deregistration process takes about ꢀ0 seconds to complete.  
Troubleshooting  
If you have difficulty with your telephone, please try the suggestions below.  
I cannot add and connect my cell phone to the telephone base.  
• Make sure you have cellular coverage.  
• Make sure your cell phone is compatible with your LS6191. Check the Bluetooth  
• Make sure the Bluetooth function of your cell phone is turned on. See the user’s  
manual of your cell phone for more information.  
• Make sure that your Bluetooth cell phone is not connected to any other  
Bluetooth device.  
• To connect your cell phone, make sure that your cell phone is connected and  
active on the device list.  
• Remove VTech LS6191 from your cell phone’s handsfree device history list (see  
the user’s manual of your cell phone for more information).  
• Carefully follow the pairing instructions on page ꢁ and make sure that your cell  
phone is not connected to any other Bluetooth device.  
• Turn off your cell phone, then turn it on again.  
• For some cell phones, you must authorize VTech LS6191 device in your cell  
phone’s Bluetooth feature. See the user’s manual of your cell phone for  
more information.  
• Manually connect your cell phone to VTech LS6191. Refer to the user’s manual  
of your cell phone for more information.  
• Reset the telephone base. Unplug the unit’s electrical power. Wait for  
approximately ꢀ5 seconds, then plug it back in. Repeat the above suggestions.  
ꢀꢀ  
 
I cannot find VTech LS6191 on my cell phone.  
• Make sure that the telephone base is in discoverable mode.  
• Make sure that you manually set your cell phone to search for devices.  
• Remove VTech LS6191 from your cell phone’s handsfree device history list (see  
the user’s manual of your cell phone).  
• Turn off your cell phone, then turn it on again.  
• Reset the telephone base. Unplug the unit’s electrical power. Wait for  
approximately ꢀ5 seconds, then plug it back in. Repeat the above suggestions.  
I don’t know how to search for or add new devices on my cell phone.  
• Most cell phones have the Bluetooth feature in the connection or setup menus.  
Please refer to the user’s manual of your cell phone.  
• In general, press the menu key on your cell phone, then look for the Bluetooth  
menu in the settings or connection menu. In the Bluetooth menu, select the option  
to search for or add new devices.  
Can the LS6191 help the poor cell phone reception in my house?  
If your cell phone has poor reception in your home, the LS6191 cannot improve  
the reception. However, if there is a location in your house with better reception,  
you can leave your cell phone at that location while you use the LS6191 cell  
line. In order for this to work, the telephone base must be within 30 feet of the  
cell phone.  
The PIN on the telephone base does not work.  
• Make sure you enter the correct PIN. The default PIN is 0000.  
My telephone does not work at all.  
• Make sure the battery is installed and charged correctly. For optimum daily  
performance, return the handset to the telephone base after use.  
• Make sure the power adapter is securely plugged into an outlet not controlled by  
a wall switch.  
Make sure the telephone line cord is plugged firmly into the telephone base and  
the wall jack.  
• Unplug the electrical power to the telephone base. Wait for approximately  
ꢀ5 seconds, then plug it back in. Allow up to one minute for the cordless handset  
and telephone base to synchronize.  
• Charge the battery in the handset for up to ꢀꢀ hours.  
• If the battery is completely depleted, charge the handset for at least 30 minutes  
before use.  
• Remove the battery and then install it again. If that still does not work, it may be  
necessary to purchase a new battery.  
• Disconnect the telephone base from the telephone wall jack and plug in a working  
telephone. If the other telephone does not work, the problem is probably in the  
wiring or telephone service. Contact your telephone service provider.  
I cannot dial out.  
• Try all the above suggestions.  
• Make sure there is a dial tone before dialing. It is normal if the handset takes a  
second or two to synchronize with the telephone base before producing a dial  
tone. Wait an extra second before dialing.  
• If other telephones in your home are having the same problem, the problem is in  
the wiring or telephone service. Contact your telephone service provider (charges  
may apply).  
• Eliminate any background noise. Mute the cordless handset before dialing, or dial  
from another room in your home with less background noise.  
• If you have changed your telephone service to digital service from a cable  
company or a VoIP service provider, the telephone line may need to be rewired to  
allow all existing telephone jacks to work. Contact your service provider for more  
information.  
The answering system does not answer after the correct number of rings.  
• Make sure the answering system is on. When the answering system is on,  
ANS ON should display on the handset and the telephone base.  
• If toll saver is selected, the number of rings changes to two when there are new  
messages waiting.  
• If the memory is full or if the answering system is off, the answering system  
answers after ꢀ0 rings.  
• In some cases, the answering system is affected by the ringing system used by  
your telephone service provider.  
• If you subscribe to voicemail service, change the number of rings so that your  
answering system answers before your voicemail answers. To determine how  
many rings activate your voicemail, contact your telephone service provider.  
• If there is a fax machine connected to the same telephone line, try disconnecting  
the fax machine. If that solves the problem, consult your fax machine  
documentation for information on compatibility with answering systems.  
ꢀ2  
 
The answering system does not record messages.  
• Make sure the answering system is on.  
• When the answering machine memory is full, it does not record new messages  
until some old messages are deleted.  
• If you subscribe to voicemail service, change the number of rings so that your  
answering system answers before your voicemail answers. To determine how  
many rings activate your voicemail, contact your telephone service provider.  
• If there is a fax machine connected to the same telephone line, try disconnecting  
the fax machine. If that solves the problem, consult your fax machine  
documentation for information on compatibility with answering systems.  
The messages on the answering system are incomplete.  
• If a caller leaves a very long message, part of it may be lost when the answering  
system disconnects the call after the preset recording time.  
• If the memory on the answering system becomes full during a message, the  
answering system stops recording and disconnects the call.  
• If the caller’s voice is very soft, the answering system may stop recording and  
disconnect the call.  
I accidentally set my LCD language to Spanish or French, and I don’t know  
how to change it back to English.  
• While the handset is not in use, press MENU and then enter 364 to change  
the handset LCD language back to English.  
• While the telephone base is not in use, enter 364 # and then press  
change the base LCD language back to English.  
to  
Common cure for electronic equipment.  
• If the telephone is not responding normally, put the cordless handset in the  
telephone base. If it does not respond, try the following (in the order listed):  
ꢀ. Disconnect the power to the telephone base.  
2. Disconnect the battery on the cordless handset.  
3. Wait a few minutes before connecting power to the telephone base.  
ꢁ. Install the battery again and place the cordless handset in the telephone base.  
5. Wait for the cordless handset to synchronize with the telephone base. Allow up  
to one minute for this to take place.  
Important safety instructions  
When using your telephone equipment, basic safety precautions should always be followed to reduce the  
risk of fire, electric shock and injury, including the following:  
ꢀ. Read and understand all instructions.  
2. Follow all warnings and instructions marked on the product.  
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a dry  
non-abrasive cloth for cleaning.  
ꢁ. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or a  
swimming pool, or in a wet basement or shower.  
5. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.  
6. Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation.  
To protect them from overheating, these openings must not be blocked by placing the product on a soft  
surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat  
register. This product should not be placed in any area where proper ventilation is not provided.  
7. This product should be operated only from the type of power source indicated on the marking label. If you  
are not sure of the type of power supply in your home or office, consult your dealer or local power company.  
8. Do not allow anything to rest on the power cord. Do not install this product where the cord may be  
walked on.  
9. Never push objects of any kind into this product through the slots in the telephone base or handset  
because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind  
on the product.  
ꢀ0. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service  
facility. Opening or removing parts of the telephone base or handset other than specified access doors  
may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock  
when the product is subsequently used.  
ꢀꢀ. Do not overload wall outlets and extension cords.  
ꢀ2. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the  
following conditions:  
When the power supply cord or plug is damaged or frayed.  
If liquid has been spilled onto the product.  
If the product has been exposed to rain or water.  
If the product does not operate normally by following the operating instructions. Adjust only those  
controls that are covered by the operation instructions. Improper adjustment of other controls may  
result in damage and often requires extensive work by an authorized technician to restore the  
product to normal operation.  
If the product has been dropped and the telephone base and/or handset has been damaged.  
If the product exhibits a distinct change in performance.  
ꢀ3. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric  
shock from lightning.  
ꢀꢁ. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances, a  
spark may be created when the adapter is plugged into the power outlet, or when the handset is replaced  
in its cradle. This is a common event associated with the closing of any electrical circuit. The user should  
not plug the phone into a power outlet, and should not put a charged handset into the cradle, if the  
phone is located in an environment containing concentrations of flammable or flame-supporting gases,  
unless there is adequate ventilation. A spark in such an environment could create a fire or explosion.  
Such environments might include: medical use of oxygen without adequate ventilation; industrial gases  
(cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.  
ꢀ5. Only put the handset of your telephone next to your ear when it is in normal talk mode.  
ꢀ6. The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are  
not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.  
SAVE THESE INSTRUCTIONS  
ꢀ3  
 
Precautions for users of implanted cardiac pacemakers  
Cardiac pacemakers (applies only to digital cordless telephones):  
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary  
evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers.  
Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:  
Pacemaker patients  
Should keep wireless telephones at least six inches from the pacemaker.  
Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it  
is turned ON.  
Should use the wireless telephone at the ear opposite the pacemaker.  
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using  
wireless telephones.  
Operating range  
This cordless telephone operates with the maximum power allowed by the Federal Communications  
Commission (FCC). Even so, this handset and telephone base can communicate over only a certain  
distance - which can vary with the locations of the telephone base and handset, the weather, and the  
layout of your home or office.  
When the handset is out of range, the handset displays Out of range or no pwr at base.  
If there is a call while the handset is out of range, it may not ring, or if it does ring, the call may not connect  
well when you press  
or . Move closer to the telephone base, then press  
or to answer the call.  
If the handset moves out of range during a telephone conversation, there may be interference. To improve  
reception, move closer to the telephone base.  
ECO mode  
This power conserving technology reduces power consumption for optimal battery performance. The ECO  
mode activates automatically whenever the handset is synchronized with the telephone base.  
Maintenance  
Taking care of your telephone  
Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.  
Avoid rough treatment  
Place the handset down gently. Save the original packing materials to protect your telephone if you ever  
need to ship it.  
Avoid water  
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with  
wet hands. Do not install the telephone base near a sink, bathtub or shower.  
Electrical storms  
Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety,  
take caution when using electrical appliances during storms.  
Cleaning your telephone  
Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a dry  
non-abrasive cloth. Do not use dampened cloth or cleaning solvents of any kind.  
Remember that electrical appliances can cause serious injury if used when you are wet or standing in  
water. If the telephone base should fall into water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE  
POWER CORD AND TELEPHONE LINE CORD FROM THE WALL. Then remove the telephone by the  
unplugged cords.  
About cordless telephones  
Privacy: The same features that make a cordless telephone convenient create some limitations.  
Telephone calls are transmitted between the telephone base and the cordless handset by radio  
waves, so there is a possibility that the cordless telephone conversations could be intercepted by radio  
receiving equipment within range of the cordless handset. For this reason, you should not think of  
cordless telephone conversations as being as private as those on corded telephones.  
Electrical power: The telephone base of this cordless telephone must be connected to a working  
electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made  
from the cordless handset if the telephone base is unplugged, switched off or if the electrical power  
is interrupted.  
Potential TV interference: Some cordless telephones operate at frequencies that may cause  
interference to televisions and VCRs. To minimize or prevent such interference, do not place the  
telephone base of the cordless telephone near or on top of a TV or VCR. If interference is experienced,  
moving the cordless telephone farther away from the TV or VCR often reduces or eliminates  
the interference.  
Rechargeable batteries: Exercise care in handling batteries in order not to create a short circuit with  
conducting material such as rings, bracelets and keys. The battery or conductor may overheat and  
cause harm. Observe proper polarity between the battery and the battery charger.  
Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not  
burn or puncture the battery. Like other batteries of this type, if burned or punctured, they could release  
caustic material which could cause injury.  
The RBRC® seal  
The RBRC® seal on the nickel-metal hydride battery indicates that VTech  
Communications, Inc. is voluntarily participating in an industry program to collect and  
recycle these batteries at the end of their useful lives, when taken out of service within  
the United States and Canada.  
The RBRC® program provides a convenient alternative to placing used nickel-metal  
hydride batteries into the trash or municipal waste, which may be illegal in your area.  
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery  
at local retailers participating in the RBRC® program or at authorized VTech product  
service centers. Please call 1 (800) 8 BATTERYTM for information on Ni-MH battery  
recycling and disposal bans/restrictions in your area. VTech’s involvement in this  
program is part of its commitment to protecting our environment and conserving  
natural resources.  
RBRC® is a registered trademark of Rechargeable Battery Recycling Corporation.  
ꢀꢁ  
 
Limited warranty  
What does this limited warranty cover?  
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or  
“you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects  
in material and workmanship, pursuant to the following terms and conditions, when installed and used  
normally and in accordance with the Product operating instructions. This limited warranty extends only to  
the Consumer for Products purchased and used in the United States of America and Canada.  
What will VTech do if the Product is not free from defects in materials and workmanship during the  
limited warranty period (“Materially Defective Product”)?  
During the limited warranty period, VTech’s authorized service representative will repair or replace at  
VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new  
or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or  
refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment.  
Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the  
repaired or replacement Products to you in working condition. You should expect the repair or replacement  
to take approximately 30 days.  
How long is the limited warranty period?  
The limited warranty period for the Product extends for ONE (ꢀ) YEAR from the date of purchase. If VTech  
repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited  
warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date  
the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year  
warranty; whichever is longer.  
What is not covered by this limited warranty?  
This limited warranty does not cover:  
ꢀ. Product that has been subjected to misuse, accident, shipping or other physical damage, improper  
installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or  
2. Product that has been damaged due to repair, alteration or modification by anyone other than an  
authorized service representative of VTech; or  
3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or  
cable or antenna systems; or  
ꢁ. Product to the extent that the problem is caused by use with non-VTech accessories; or  
5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have  
been removed, altered or rendered illegible; or  
6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or  
Canada, or used for commercial or institutional purposes (including but not limited to Products used for  
rental purposes); or  
7. Product returned without a valid proof of purchase (see item 2 below); or  
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems  
outside the unit.  
How do you get warranty service?  
To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call  
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and  
features may save you a service call.  
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and  
are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location.  
VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling  
charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure  
is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty,  
VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity.  
You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this  
limited warranty.  
What must you return with the Product to get warranty service?  
ꢀ. Return the entire original package and contents including the Product to the VTech service location along  
with a description of the malfunction or difficulty; and  
2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and  
the date of purchase or receipt; and  
3. Provide your name, complete and correct mailing address, and telephone number.  
Other limitations  
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other  
written or oral communications related to this Product. VTech provides no other warranties for this Product.  
The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other  
express warranties. No one is authorized to make modifications to this limited warranty and you should not  
rely on any such modification.  
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights,  
which vary from state to state or province to province.  
Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an  
unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase.  
Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation  
may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential,  
or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other  
associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use  
of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential  
damages, so the above limitation or exclusion may not apply to you.  
Please retain your original sales receipt as proof of purchase.  
FCC, ACTA and IC regulations  
FCC Part 15  
This equipment has been tested and found to comply with the requirements for a Class B digital device  
under Part ꢀ5 of the Federal Communications Commission (FCC) rules. These requirements are intended  
to provide reasonable protection against harmful interference in a residential installation. This equipment  
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with  
the instructions, may cause harmful interference to radio communications. However, there is no guarantee  
that interference will not occur in a particular installation. If this equipment does cause harmful interference  
to radio or television reception, which can be determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Changes or modifications to this equipment not expressly approved by the party responsible for  
compliance could void the user’s authority to operate the equipment.  
This device complies with Part ꢀ5 of the FCC rules. Operation is subject to the following two conditions:  
(ꢀ) this device may not cause harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation. Privacy of communications may not  
be ensured when using this telephone.  
ꢀ5  
 
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy  
that can be safely absorbed by a user or bystander according to the intended usage of the product. This  
product has been tested and found to comply with the FCC criteria. The handset may be safely held  
against the ear of the user. The telephone base shall be installed and used such that parts of the user’s  
body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more.  
This Class B digital apparatus complies with Canadian ICES-003.  
FCC Part 68 and ACTA  
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the  
Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment  
contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must  
be provided to your telephone service provider upon request.  
The plug and jack used to connect this equipment to premises wiring and the telephone network must  
comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone  
cord and modular plug is provided with this product. It is designed to be connected to a compatible modular  
jack that is also compliant. An RJjack should normally be used for connecting to a single line and an  
RJꢀꢁ jack for two lines. See the installation instructions in the user’s manual.  
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your  
telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th  
and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but  
not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your  
telephone service provider.  
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment  
connected to your telephone line, ensure the connection of this equipment does not disable your alarm  
equipment. If you have questions about what will disable alarm equipment, consult your telephone service  
provider or a qualified installer.  
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been  
corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized  
agents. For repair procedures, follow the instructions outlined under the Limited warranty.  
If this equipment is causing harm to the telephone network, the telephone service provider may temporarily  
discontinue your telephone service. The telephone service provider is required to notify you before  
interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be  
given the opportunity to correct the problem and the telephone service provider is required to inform you  
of your right to file a complaint with the FCC. Your telephone service provider may make changes in its  
facilities, equipment, operation, or procedures that could affect the proper functioning of this product. The  
telephone service provider is required to notify you if such changes are planned.  
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.  
If this product has memory dialing locations, you may choose to store emergency telephone numbers  
(e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:  
Remain on the line and briefly explain the reason for the call before hanging up.  
Perform such activities in off-peak hours, such as early morning or late evening.  
Industry Canada  
Operation is subject to the following two conditions: (ꢀ) this device may not cause harmful interference, and  
(2) this device must accept any interference, including interference that may cause undesired operation.  
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical  
specifications were met.  
The Ringer Equivalence Number (REN) for this terminal equipment is ꢀ.0. The REN is an indication of the  
maximum number of devices allowed to be connected to a telephone interface. The termination on an  
interface may consist of any combination of devices subject only to the requirement that the sum of the  
RENs of all the devices does not exceed five.  
This product meets the applicable Industry Canada technical specifications.  
Technical specifications  
Frequency control  
Crystal controlled PLL synthesizer  
Transmit frequency  
DECT frequency: ꢀ92ꢀ.536-ꢀ928.ꢁꢁ8MHz  
Bluetooth frequency: 2ꢁ02.000-2ꢁ80.000MHz  
Channels  
DECT channel: 5  
Bluetooth channel: 79  
Nominal effective range  
Power requirements  
Maximum power allowed by FCC and IC. Actual operating range may  
vary according to environmental conditions at the time of use.  
Handset: 2.ꢁV Ni-MH battery  
Telephone base: 6V DC @ ꢁ50mA  
Memory  
Directory: 200 memory locations; up to 30 digits and ꢀ5 characters  
Caller ID log: 50 memory locations; up to 2ꢁ digits and ꢀ5 characters  
The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks  
by VTech Holdings Limited is under license. VTech Holdings Limited is a member of Bluetooth  
SIG, Inc. Other trademarks and trade names are those of their respective owners.  
VTECH TELECOMMUNICATIONS LTD.  
A member of THE VTECH GROUP OF COMPANIES.  
Distributed in the U.S.A. by VTech Communications, Inc., Beaverton, Oregon 97008.  
Distributed in Canada by VTech Technologies Canada Ltd., Richmond, B.C. V6W ꢀL5.  
VTech is the registered trademark of VTech Holdings Limited.  
Copyright © 20ꢀ2 for VTECH TELECOMMUNICATIONS LTD.  
9ꢀ-00697ꢀ-050-ꢀ00  
All rights reserved. Printed in China.  
ꢀ6  
 

Tascam Cassette Player 202mkIV User Manual
Tascam Home Theater System SN29401376 User Manual
Teac Home Theater System AG D8850 User Manual
Tektronix Welding System AWG5000 Series User Manual
Toshiba All in One Printer e STUDIO4500c User Manual
Toshiba Digital Camera PDR M700 User Manual
Toyota Automobile SIENNA User Manual
Tyan Computer Personal Computer N3600QX User Manual
Tyco Electronics Two Way Radio P5300 User Manual
Univex Lawn Mower 35692 User Manual