VTech Two Way Radio VT 1311 User Manual

when both radios are tuned to the same  
channel.  
If someone else is using the channel you have  
selected use the CTCSS (Continuous Tone  
Coded Squelch System) feature for silent  
monitoring.  
Please take a few minutes to read this manual  
carefully. The information described below will  
allow you to obtain maximum performance  
from your radio.  
button to select the desired channel.  
interference.  
Communication  
range  
depends on the environment and will be  
adversely affected by concrete structures,  
indoor or in vehicle operation.  
To Adjust the Receive Volume  
1. Press the MODE button one or more times  
until “VOL” appears and flashes.  
2. Press the UP/DOWN buttons to select the  
desired volume.  
V-Talk  
VT 1311  
Channel Scan  
1. Turn the radio off.  
2. Turn the radio on while pressing the DOWN  
button. “SC” will appear for indication.  
You can change the scan direction by  
pressing the UP/DOWN button.  
3. The scan functioin will stop if there is a  
signal present on a channel, and will  
resume about 3 seconds after signal drop  
out.  
4. Press the MODE button or turn the radio off  
to exit channel scan.  
Note:  
1. During scanning, the CTCSS feature is  
disabled.  
2. Transmitting is allowed during scanning.  
When the PTT is released, the radio will  
wait for an answer for 5 seconds before  
starting to scan again.  
To Select A CTCSS Code  
Antenna  
1. Press the MODE button one or more times  
until “CTS” appears and flashes.  
External  
Speaker  
and  
Microphone  
Jacks  
2. Press the UP/DOWN buttons to select the  
desired CTCSS tone (“oF” means the  
CTCSS feature is disabled).  
BATTERIES  
This radio operates with  
batteries.  
3
AAA alkaline  
To Receive  
LED  
Indicator  
When an incoming signal is received, the LED  
indicator will go green.  
To Install:  
1. Firmly remove the battery cover.  
2. Insert 3 AAA batteries.  
UP  
Monitor  
DOWN  
This feature is used to check activity on the  
current channel before transmitting. You can  
also adjust the volume by pressing the  
UP/DOWN button when monitoring.  
Press the MODE button for 1 second, and the  
monitor feature will be activated until the  
MODE button is released.  
3. Replace the battery cover carefully.  
MODE  
Low Battery Alert:  
POWER  
When the batteries are low, the display on the  
radio will flash for indication, and transmitting  
will be disabled. Replace the batteries to  
avoid interrupted use.  
Microphone  
PTT  
CTCSS Code Scan  
(Push to Talk)  
Note:  
To Transmit  
This feature helps you to detect and set the  
correct CTCSS code for a received signal. By  
1.Please remove the batteries if they are  
discharged or before storing your radio  
1. Do not transmit if someone is talking on the  
operating channel.  
Thank you for purchasing this license-free  
personal communication V-Talk two-way  
radio for Family Radio Service (FRS) designated  
frequencies.  
monitoring  
a
received signal, you can  
for  
corrode over time, and if left in the  
radio may cause permanent  
damage.  
2.The use of high capacity batteries is  
extended  
periods.  
Batteries  
2. Press the PTT (Push-To-Talk) button and the  
LED indicator will go red.  
3. Hold the radio a few inches from your  
mouth, and speak in a normal voice into  
the microphone.  
4. Release the PTT button to receive again.  
Note:  
determine its correct CTCSS code used on  
the air.  
1. Turn the radio off.  
2. Turn the radio on while pressing the UP  
button. “SC” and “CTS” will appear for  
indication.  
3. Scan activates only when a signal is  
received and stops when the correct  
CTCSS code is decoded, which will then  
be selected automatically.  
IMPORTANT  
Please read this manual carefully and  
completely before attempting operation.  
recommended  
operating life  
changes.  
for  
between  
maximum  
battery  
When the batteries are low, transmitting  
could be disabled. If you press the PTT  
key, the LCD will be dark and a beep  
sound will be generated for indication.  
Please replace the batteries to avoid  
interrupted use.  
WARNING  
Do not operate the radio when driving a  
vehicle or riding a bicycle.  
4. Press the MODE or PTT buttons, or turn the  
radio off to exit CTCSS code scan mode.  
Note:  
Do not operate the radio near unshielded  
electrical blasting caps or in an explosive  
atmosphere. An explosion or fire may  
result.  
When Key Lock feature enabled,  
Channel Scan and CTCSS Code Scan  
can not be activated.  
Time-out Timer  
This feature helps extend battery life. The  
radio will beep a warning tone and stop  
transmitting if the PTT button is pressed for 30  
seconds or 3 minutes (default) continuously.  
The “oF” also appears to indicate The time-  
out Timer is activated. You can change the  
time-out timer from 30 seconds to 3 minutes  
(default) as follows.  
3 AAA BATTERY  
Changing or modifying the radio could  
void the user’s authorization to operate  
this radio. Never open your radio case.  
Backlight Control  
Normally, the LCD backlight will turn on when  
any button except the PTT is pressed and turn  
off again after 5 seconds except when the  
radio is scanning.  
OPERATION  
FCC INFORMATION  
To Turn the Radio On  
Do not open your radio to make any internal  
adjustment. Your radio is set to transmit a  
regulated signal on an assigned frequency. It  
is against the law to alter or adjust the settings  
inside the radio to exceed those limitations.  
1. Press the POWER button for 1 second. The  
radio will beep and the operating channel  
number will appear to indicate the radio is  
on.  
The backlight can be permanently  
illuminated by the following procedure.  
1. Turn the radio off.  
2. Turn the radio on while pressing the MODE  
button. “bL”(Backlight) will appear for  
indication.  
To return to the normal backlight feature,  
repeat the same procedure described  
above and “oF” will appear for indication.  
1. Turn the radio off.  
2. Turn the radio on while pressing the PTT  
button. The time-out timer will switch  
between 30 seconds and 3 minutes.  
2. To turn the radio off, press the POWER  
button for 1 second. The radio will beep to  
confirm.  
INTRODUCTION  
With the VTech two-way radio, you can talk  
with another person who has a similar radio  
Communication Range  
To Select an Operating Channel  
It is recommended that you do not use the  
radios closer than 5 feet due to heavy  
Turn the radio on, then press the UP/DOWN  
 

Tascam CD Player CD 200BT User Manual
Texas Instruments Network Card TNETE100A User Manual
Timex Clock Radio T237 User Manual
Toshiba Projector TDP P8 User Manual
Trane Furnace 22 1671 04 0702 EN 7 User Manual
Transition Networks Cable Box DVP 5140K User Manual
Tricity Bendix Cooktop TBD950 User Manual
U Line Ice Maker ADA24R User Manual
Vivitar Camcorder Accessories Tripod Video Equipment User Manual
Wayne Dalton Garage Door Opener 341785 User Manual